I have way to much time to waste raking up the leaves & bagging them but I am still working on some of the models I got & this time it's the Bluenose kit that had all the masts broken off . I started it while our model boat club was at the Caledonia wood show . I try my best to get people to be interested in model boat building while I'm repair the model. The sails are up & now for the rat lines & a little painting & a few touch up here & there!

U.S. Navy PBR 31Mkll. Patrol Boat River.
This is a vessel that I'm building from scratch. To achieve accuracy I will be using a Tamiha 1/35 scale kit and scaling that kit up to 1/9th scale for the vessel I am building. it will measure up to almost 1 metre in length.

"Searcher" was a Graham Goodchild design offered as a free plan in "Model Boats" in December 1981. Here is my version , many years in the building and finally nearing completion. Access to the hull on the original design was via a hatch above the cockpit - I had no faith in my ability to make it water tight so went for removable grp. hatches. The model is activated by a reed switch just in front of the rear hatch, which saves me the hassle of doing/undoing all the nuts (this had not been fitted when I took the first picture). The rear hatch gives me easier access to the drive coupling. The name "Nimbus2" is in honour of one of Dan Dare's spaceships in the Eagle comic. The third picture shows the ship in its final state with added 'enhancements' and working lights.

Trying to learn to use this forum properly I am publishing a video that shows an experiment I did to find out how fast the stepper motor could turn. I am using in my model of the sailboat Carina 2 stepper motors like the one shown in the video to work as a winch to control the position of the sails in a system solution where I am realizing this my own way to implement the sheets as shown on the original sailboat Endeavour. This requires my sheet control system to control the length of the sheet of the mainsail i.e. over a range of 8.3 meters. This requires the drum which is turned by the stepper motor to make 21 full turns. Details will be published in my report from scratch of building my Carina.

aero-naut mowe 2 kit. my first rc model boat with a few extras.The kit was ok to build but the prop coupling was a length of silcone tube ? it spun off at the first test run.This was the start of me fitting universal couplings to my boats.The company were being mean using a cheap piece of tube.It runs very quiet and smooth but needed a lot of front end ballast .i made this to try and drag my grandson away from his ipad,phone and the game of fortnite .I tried to get him to help build and run it but to no avail.I now am enjoying a second childhood building boat kits !

Hi Model boat enthusiasts,
This is a photo of almost completed 2 model boats I have almost completed. The Sea Queen 50 years old find. it was found in an attic in a kit. The kit was in a very poor state and most of the timberwork had to be glued back together or remade. I had no plans for it and had to source a copy from the Model Boat website. it is a very nice model. The pilot boat was scratch built and sails very nicely. I have been building boats for about 30years and have built over 25 boats, scratch built all of them. I have included photos of some of my boats.

My newest build , Billing Boats Fairmount Alpine
i start building for one years ago , i have mount bowtruster
and start with all lamps and things , i going to mount an radiocontrolled winch on deck and radiocontrolled cranes
more pictures is comming

Greetings from Germany! I've been out of the net for a while and rebuilding this boat with a totally new superstructure, paint job and electronics. I obtained the fiberglass hull measuring 24.5 X 9 inches from a California fellow via E-bay. Formerly a 45-footer Chris Craft at 1:24 scale, this updated vessel was inspired on a 1970s 30-footer Chris Craft Tournament Fisherman and on 1970s 28 and 33-footer Bertram boats. 😁 The Chris Craft in the attached picture from an early days brochure was the very only Chris Craft utilizing a Deep-Vee hull. The story goes that they apparently copied their boat following the lines of a Bertram 28 based on famed boat designer Ray Hunt. Bertram sued in court and Chris Craft ended up building less than 200 boats of this type. After all, the Chris Craft vessel ended up being better than the Bertram in terms of cabin space and overall value. Highly cherished within the American sports fishing community, many of these boats are still up and running.

My 1st excursion into model boat building about a year ago....steep learning curve!!!

Currently powered by 2 x 480 brushed on 11.1v, both motors independently controlled by 2 ESC but soon to be refitted with 2x 1000KV brushless.

Planes beautifully and with twin rudders turns on a sixpence!

Guess most of you have heard of the Khetanna, Jabba The Hut's sail barge from Star Wars. I looked around on the net and to my big surprise, the search engines did not spit out radio controlled versions of this model. Which made me think, and then decide to built my own.
It is scratch build, based on a "scudder" hull, a design by Glenn G. I printed a few pictures of Khetanna from the net and used those for guidance in the process.
The superstructure is a combination of balsa and ply wood. in the Star Wars tradition, the boat is propelled by a jet propelled engine. To finish it off, a Lego version of Jabba was added for extra detail.
It was a fun and fast project to built, maybe a dozen or so evenings.
(scratch) building is my passion and only sail the boats with my son about once a month. We've got a pond near Newcastle (AUS) harbour which is pretty good (providing there's no weed in it) but the disadvantage of this pond is salt water, meaning a proper rinse of the models is needed after each sailing session. Recently we have moved our sailing sessions as well to the liberty pond in town. The model captures the audience, the vast majority recognize the Khetanna immediately.
Happy sailing.

Jeroen

This is the first post Iv put on any site so ......here goes.
I have 18 boats ..................Yes 18 , and Im still married lol !
Love this boat , just going through a re fit , power wise etc,
just was not powerful enough. and too clean .
so decided to try my hand at weathering .
a bit daunting building something "pristine '' ish
then trying to make it better by roughing it up .

Scratch built 1/48 scale Mersey ferry Snowdrop in current use on the Mersey (ex Woodchurch)
Model interiors fitted out with tables chairs people etc and 72 leds light to Illuminate the interior saloons.
Just completed and maiden voyage on Hoylake Lake on the Wirral.
2.4Ghz radio and a bilge pump just in case. Sails a treat with 100 passengers. Extensive use of plasticard on superstructure. Fibreglass hull from own mould.
See sailing location at www.hoylakemodelboatclub.co.uk
Our club can supply the hull if you want to have a go at building one.