Search
3,160 posts for “brushless”
Page 75 of 113
Harbour
SHB Triton Harbour Master
Harbour Master, my first experiment with sensored brushless motors, ultra quiet and smooth very successful
Forum
Reply
Re: 46 Inch Crash Tender - 6 days on
My 46 inch Crash Tender has a Leopard Brushless Motor plus a Hawk Fusion 100amp ESC driving a 50mm 3 blade brass prop. It performs better than i expected when i completed the model three years ago and is still in use and reliable and looks …
Forum
Reply
Re: RTTL IN SLOW MO
Goes like a brushless motor set up. Good job
Forum
48inch Fairey Huntsman
… e fibreglass hull ) I would like assistance/advice on which brushless motor would give the boat a fair turn of speed all advice will be greatly appreciated With Thanks Little Charlie
Forum
48inch Fairey Huntsman
… cre performance. I plan on changing to a LiPo battery and a brushless motor and would be looking at something like an Overlander Thumper 5045/10 720 kV. This has plenty of torque to get a heavy boat moving and as you can use 3 to 8s batteri …
Forum
48inch Fairey Huntsman
… e hobby after my wife passed away and have not a clue about brushless motors that is why I am asking for a recomendation for a brushless motor unless of course somebody can tell me where I can procure a 25cc Fox engine (the importers used t …
Blog
H.M.S BRAVE BORDERER
… eed using the centre screw brushed motor and then the outer brushless screws on the 2S battery 3) Max. speed using the centre screw brushed motor and then the outer brushless screws on the 3S battery. Because the pond is small, was unable t …
Forum
Fairmile c class maiden voyage
… m ratio, destroyer with twin 540s, and will use one (or the Brushless P40 version) in my triple screw PTB. Beauty of the hardware mixer is that you can switch off all the aircraft / heli mixer functions at the TX and just use one stick for …
Forum
Mistery box
… oyer and later in my Sea Scout before the latest refit with brushless. It should work fine with your renovated Supermarine on a 7.2V NiMh or a 2S LiPo Cheers, Doug
Blog
H.M.S. BRAVE BORDERER
… d the ESCs and Rx. These changes allowed the removal of the brushless motor selection circuitry and improved the tractability of the system. As the videos show, a plane can be achieved with both 2S and 3S batteries. With the 3S the plane is …
Forum
Fairmile c class maiden voyage
… n the $$ really Not sure if you are using Lipos, brushed or brushless setup but either way sounds like 2x 3s 3000mah 20c lipos should work, especially if your motors are brushed 12v , also maybe try reducing the prop pitch or diam to take a …
Forum
Fairmile c class maiden voyage
… uter shafts : 2 x Turnigy AquaStar 2842-2800KV Water Cooled Brushless Outrunner Motor 2 x HobbyKing 50A Boat ESC 4A UBEC Centre Shaft : 1 x 550 Brushed motor 1 x Quickrun 1080 ESC All shafts have 35mm brass screws Model is about 35" OL leng …
Forum
Fairmile c class maiden voyage
Did this on my Brave Borderer. 2 x brushless motors on outboard screws and brushed on centre using a third ESC. Works well
Forum
Tamar Lifeboat propellers
… s. Good speed from the supplied props with kit running with brushless Tornado 3536 1050kv on 3s lipo. Any recommendations of what to go for would be helpful. Thanks
Harbour
Lesro Sportsman II
Lesro Sportsman II Nearing completion, going brushless with a 2000kv, & 90a ESC, water trials on Sunday :-)
Forum
Tug towing
… output if you find you need one) in my HSL (2x 2845 2000kv brushless in-runners,- 1 ESC per motor on 2cell 2200mah LiPos ) and they don't even get warm (30mm 3 blade props with a high pitch - around 40mm I think - Chinese from AliExpress a …
Forum
Tug towing
Can anyone recommend a good brushless motor and esc for tug towing please?
Blog
HMS BRAVE BORDERER
… s. Have always been concerned about the “stuttering” of the brushless motors. This is more correctly identified as “cogging”, often caused by incorrect motor timing. Changed the timing to “Automatic” from the incorrect previous setting, whi …
Forum
Tug towing
… ced very sedate performance. The Sea Scout now has a 1000kV brushless. Two of these Decaperms should give a good amount of 'tug' to overcome considerable wind. I'm wondering if the superstructure of your ship is offering too much 'attack ar …
Forum
Tug towing
… articular voltage and will wear badly with increased volts. Brushless do not have this problem, and can run on a wide variety of voltages. Running at 24v is quite possible... The ESC you want for a brushless is simply one that can handle th …
Forum
Motor, speed controller
… ures, and are usually designed for cars alone. I agree that brushless tend to have jerky starts which are not good for rescues. Ideally bow thrusters or even pod motors would be best for manoeuvrability. One other feature which might be use …
Forum
Tug towing
… ure of the gear ratio as I understand the lower the kv of a brushless motor the higher the torque so hoping someone might be able to help me work out what size speed controller would be required to run a 800kv brushless motor
Forum
Motor, speed controller
PS: Attached is the manual for my 16BL30 brushless ESC. Note instruction for 'Running Mode' in section 5. I use Option 3; Forward / Reverse only.
Forum
Motor, speed controller
… componentshop.co.uk/p94-dual-esc-and-mixer-2-x-20-amps.html Brushless can be tricky to set up for smooth starts. 'Out of the box' they tend to jump off like scalded cats. Which is not what you want for rescue operations Some ESCs allow you …
Forum
Motor, speed controller
… . That probably means using a brushed controller, since the brushless reversing ones tend to: a - be expensive b - be designed for cars and have this annoying 'brake' function which means that you have to action reverse with a double stick …
Forum
Motor, speed controller
Brushed or brushless? And what size motor?
Forum
Reply
Re: Hellenic Navy - La Combattante IIIb class Fast Attack Craft
It is powered by 2 720kV brushless motors. You can find details about the boat in my Boat Harbour including photos of the internals.
Forum
Noodle Jet Boat
… n (ready-split!) for the inflatable section, had a standard brushless prop and used a servo hidden in a dummy outboard to swing the outboard for use as a rudder. I never completed the boat, and did not publish the plans, but if there is som …