Search
3,160 posts for “brushless”
Page 39 of 113
Harbour
LESRO SPRITE
Not sure what the run time will be with the new brushless set-up, so I've put 15mins as a start point; I know I can get 10-12+ mins with this size motor and a 3200mAh 4s Lipo in a 63ins span KK Super Sixty trainer plane revving an11x4" prop …
Forum
Sprite
… will be using in this boat yet - other than that it will be brushless (!), but it could be an in-runner as I have had one on my bench for several years that is well overdue to be put to work! Bob.
Forum
Sprite
Sprite Plus - fitting the motor mounting baseplate. With a brushless motor fitted onto the alloy water-cooled mount and joined to the 5mm prop shaft with a solid coupling, the angle of the motor mount assembly can be clearly seen. The carbo …
Forum
Sprite
… and fitted. Having fitted the solid 5mm x 5mm coupling to a brushless motor and then screwing this assembly in-between the carbon "side spats" of the motor mount, I had the precise location for the motor to be fitted after it is clamped ont …
Forum
Reply
Re: Vosper
I’m glad you are NOT putting in a brushless motor, because when I bring my model along side yours, we can go out on patrol together without me chasing your wake. We will look good providing support the bigger vessels of the fleet!
Forum
Reply
Re: Classic Model Power Boats
… s I just bought one 90% finished with 6 channel 2.4G radio, brushless 3542-1450kv. 60 Amp ESC. Only to finish adding the fittings ,interior and maybe the funny wing things on the sides which are missing. Harry
Forum
Reply
Re: Fairey Huntresses
… v lead acid battery. Very heavy though. I am going to put a brushless in it at some point and use a LiPo battery. SHould go a lot better, I did run it a mile up the River Thurne in Norfolk a few yewars back and under Potter Heigham Bridge, …
Forum
Reply
Re: Fairey Huntresses
… of years ago. Yes, it will certainly go a lot better with a brushless motor and a Lipo. Do you need the template for the windscreen? Chris
Forum
Reply
Re: Classic Model Power Boats
… d that are fuel soaked too. A restoration and conversion to brushless motor power would make this into a very nice Classic Model Power Boat that would be really good to see on the water again. Bob.
Forum
Reply
Re: Aerokits Sea Commander. Strange Handling ?
… a Queen restoration followed by a good motor mount to fit a brushless out-runner. I am not so sure about the size of propeller yet, but 50mm could be a good size to start with, but when the boat can be run for the first time, the experiment …
Forum
Reply
Re: Aerokits Sea Commander. Strange Handling ?
Hi Zooma My 46" crash Tender has a 420 kv brushless on 6 S and a 2 blade 52 mm prop. RPM about 10000 !!! So I have a 5055-700 kv brushless and on 4S about 10360 rpm. So that's my base start. As for spray rails I am not planning on adding th …
Forum
120 years of modelboat history
… has a MFA 800 brushed motor in it. I am about to change to brushless soon. I also have 2 x 3ft Anglia Model Shop Fibre Glass Huntsman hulls that I can still build to how ever I wish to put superstructures on. I do have the parts drawn out …
Forum
Reply
Re: Classic Model Power Boats
… ist the 34" F1 tunnel hull with a K&B converted outboard to Brushless. I am thinking of putting that on Ebay as I am thinning out a lot of my boats as I have so many. A couple of those cheapy NQD R/C ready to run boats as well . I had about …
Forum
Reply
Re: Classic Model Power Boats
… (was meant to have a Zenoah sold that off) will now have a brushless. 28" R.A.F. CRASH TENDER. Built from Balsa wood from reduced 34" plans. 50" Chineese Fibreglass PT 109. ( removed the 26cc IC engine, going brushless) Proboat Miss Geico …
Forum
Reply
Re: Classic Model Power Boats
… ite" !!! I think it's about time to take her for a run. 35m brushless 920KV, 3S lipo Battery, 40mm 2 blade prop. Harry
Forum
No motor coupling
… e installation and eliminate shaft alignment issues. Modern brushless motors are light and compact, a 4mm or greater shaft should easily hold the weight. Anti rotation could just be rubber on low power motors with something more complex as …
Forum
Mixer connections
Hi, bought two of these for my RC shark, I need to mix two brushless motors and two servos. They don’t have wiring diagrams any suggestions as to how to wire them up please? I’ll be using a Futaba 6EX-PCM 1024 as it’ll be under water (hopef …
Forum
Mixer connections
… ’s worked with mixing servos, I’m just about to try it with brushless ESCs. Do I need to follow the ‘one power lead’ rule if plugging in to the mixer instead of the RX?
Forum
Mixer connections
… ColinJ2, the mixer you have there from AliExpress is marked brushless. BUT it is not just brushless it will drive a brushed esc just as well. The mixing is done before the esc is involved. It is possible the mixing has taken brushless opera …
Forum
Surpass ESC Problem?
… n the water. All other ESC that I have used in my boats for brushless motor control cut power at a pre-determined cell voltage to protect the battery. Often, following the power cut the ESC will re-set to allow you to limp back to shore wit …
Forum
Reply
Re: Classic Model Power Boats
… ppy water it creates! There are also a couple of very small brushless motors without a home laying around that would also work well in this model.......and that just adds to the list of very small reasons that I need to get a grip of ....an …
Forum
Building the Rapier
Hi why not go for a brushless eletric motor i m not go with sizes they are very fast motors Philuk
Forum
No motor coupling
… SC and motor (brushed) or between drive battery and ESC for brushless. 3. Twiddle the motor gently around until you reach the position where the current drawn is at minimum. This is then the position of perfect alignment and maximum power t …
Forum
Reply
Re: Classic Model Power Boats
… not be water-jet powered but have a conventional shaft and brushless motor set-up - just like my Rapier - because that has exceptional performance and handling that I would like to also have on this (slightly) smaller Project 3 model. Bob.
Forum
Mixer connections
Thanks Chris, yep - got two ‘Shark’ brushless ESCs ready to connect up..
Forum
Mixer connections
… iagram but hopefully you know that you need an ESC for each brushless motor?
Forum
Motor Mounts
… unts to go in a model MTB (1/32) using Overlander T3536T/06 Brushless engines - what would you recommend please. Also can you recommend a UK based supplier that has stock in and can offer next day delivers - fed up wth being pointed to Chin …
Forum
Reply
Re: Classic Model Power Boats
… th respond really nicely to being driven fast with a modern brushless motor ! Bob