This is a restoration of a launch I was given that was found in a rubbish bin on a farm here in Auckland it is an old RCM ? plan built 'Fairacre' and was pretty rotten when I received it as it is made in balsa and had been wet for quite a while. I stripped it down, re 'planked' large portions of the hull and fiber glassed it, re- built the cabin, re- marked the deck planks, fitted lights, curtains (ex Graupner Commodore bits from the 70s I had kept), stern ladder, cleats etc. it is fitted with a 540 brushed motor (originally had an old Graupner monoperm) and 70s Graupner ESC and Using 2.4 Radio gear. I still have a few things I'd like to do such as a re-wire, fitting chine spray rails, better motor and maybe some safety rails, but for now it does the job.
My dad built this over a long period of time, starting in the '80s. The hull is fibreglass and the rest is scratch built from plastic card, balsa, ply, wire and anything else he could adapt.
Although he installed the motors, props and rudders he never completed the RC installation or tested it. I inherited his boat models a few years ago and wanted to "finish the job", getting the model on the water. After installing the RC gear and batteries over the last few months, this weekend was the first sailing outside the bath at the Valley Gardens boating lake.
Happy to report that it sailed really nicely, seems to be reasonably stable although I did restrict it to calmer times when the MTBs and faster boats weren't running !
HMS Cadiz was a battle class destroyer, laid down and launched during WW2 although she didn't receive her commission until 1946 so didn't see combat with the Royal Navy, serving with the home fleet. Due to the changeover in pennant numbering she was originally allocated R09 and later, when the admiralty decided to revert to the D for Destroyer pennant numbering she was assigned D79. To reflect this my model has D79 on the starboard side and R09 on the port side.
She was sold to Pakistan in the late '50s, and renamed PNS Khaibar. She was sunk with the loss of nearly all hands in 1971 in the indo-Pakistan war.
Huson 24 RC sailboat wooden hull. I have a small fleet of these. They are extremely stable in high wind. Bought this one online in pretty good condition.
Did a lot of smoothing on the epoxy coated hull. I use West Systems epoxy because it flows so well - like paint - and doesn’t stink.
I built this from scrap wood i had lying around i bought the tanks from china the motor is a 850 mfa with a speed controller powered by a 11.1v 5000 mah battery
still in progress 😉
When I was in high school back in 1957 I built a kit of the Comet Gypsy Sloop Jr. in 2016 I found the drawings on-line for the Gypsy Jr. The boat was entered in woodworking class at our county fair where it received a blue ribbon. it has a working wheel that turns the rudder. Now I have under construction a 32 inch version that I would like to radio control. I'm not too sure how to set up or what type of servo to install.
Well done that man 👍
Unfortunately I'm not a yacheting man so can't help you directly with the setup.
BUT HEY! There's lots of yachties on this site! I've seen many discussions, threads and blogs on various yacht setups ....
Soooo ... pull your digits out guys, give the man a break and help him out with his yacht setup.
Cheers, Doug 😎
Go with swing arm servos for sail control, less trouble with the lines than winch. if room is a problem one can be used to control jibs & main. but separate controls are obviously best.
A very nice looking and efficient steam engine, I have one which is similar made by Cheddar whether it is a Proteus or not I'm not sure, I bought it in an Edwardian Steam launch which to date has never been fired up as such. Regards.
Proboat Alpha - ready to run, model of PBR, Patrol Boat Riverine, used by US Navy during Vietnam conflict, served 1967 -1972.
Images show basic detail, 1/18 scale, with crew. Bow gunner servo is linked to rudder. Comes with Navlights, looking forward to a night sail.....some painting added to weather craft, as well as painting radar housing a lighter grey....and the canvas roof over wheel house....a little artistic licence with vessel numbers......Brown Navy did'nt always have numbered vessels....but could'nt help myself.
On the pond today. Sailing well, though took on water easily over the combing into the cockpit. So back home I added a clear covering which should take care of that problem.
Proboat Aplha - ready to run.......model of Patrol Boat Riverine used by US Navy, Vietnam between 1967-72. Basic 1/18 scale able to attach small action figures for added dimension, model always look better with crew.
Great starter....already looking at larger scale military kits and really impressed with Deans Marine product range, unfortunatly little options to explore in Australia....so have to order most stuff in....vids will get better with experience...stay tuned.😉
