this boat started as a kingston mouldings hull of the
p28 fast patrol boat you get hull and plan the rest is up to the builder it is twin shafts twin rudders one speed controller a jel 6v 7amp battery AND two
545 motors

The boat is a scratch built and started life in the shed. it is a semiscale model at aprox 36inch, built with balsa wood.It is full remote control and fitted with two Mtroniks Vision 600 motors one 12volt 7ah battery,one seasprint esc.
It was built as a fun boat so I could sail with my friend Peter thomas with his variuos boats.
Several things have now been added since this boat was first built, IE smoking stacks, fireing torpedoes and magnetic pickups for colecting them. Also has working radar/moving gun + a home built bec.
Flag poles and flags/compas has been added on the superstructure.
Each motor draws 6amps at full power, I have measured the speed from one point to another at a spacing of 60mtrs, and timed at 15 seconds, but this is a bit fast for this boat as she starts to plane out of the water.
We sail her at New Brighton lake on the wirral most wednesdays. As the weather is now a bit cool I have just purchased a simular model to this at 1:48 scale 110ft island class USCG Patrol boat so I can look at them both in action when the weather picks up. Anyone wanting info can contact me via this website.

Following a significant amount of restoration this old and original Aerokits 36" Fireboat was rebuilt from a wreck to a nice, working model. A full (new) white metal fittings kit provided all the deck clutter. Like my Sea Commander, featured elsewhere on this site, I have considerably lightened much of the internal structure. it's powerd by an 800 electric motor and runs on 12v. Performance is OK with 2 channel 27Mhz radio. Perhaps the best bit is a superb triple V12 sound unit (speaker under an additional hatch behind the wheelhouse). it sounds great on the water although someone did wonder why, having gone to all the trouble to remove the old unsilenced I/C engine and go for a quiet electric unit, why then add the noise back??. The pic of the boat underway has the battery externally in the rear compartment whilst doing sonme tests. it runs at Warminster Model Boat Club, Wiltshire.

This Sea Comander was another disaster, rescued from fleabay a couple of years ago as a 50s/60s bare shell. Whilst the hull was basically sound, the model needed considerable surgery. I resisted the temptation to cover it in modern fittings and have kept it original looking. Power is an electric 800 motor on 12 volts with 2 channel 27Mhz R/C. Performance is reasonable, particularly as I have lightened the original internal structure considerably. A big 7AH battery lasts for ages but for speed I use a small 2.5AH one. Owner sails at Warminster Model Boat Club, Wiltshire.

Here is a video of our boat (Vigilant star) sailing at New Brighton boat lake on the wirral every Wednesday.

The boat is a semiscale (Coast Guard Cutter), designed by Hal-Harrison in Marine Modelling. I have doubled its size and put two 540/1 Mfa motors in, driving quanta 45mm props. She is 36" length 8" Bow, runs of one 12 volt 7Ah SLA battery.

It is made from Balsa/Fibreglass resin. Runs well no leaks to date. Gerry.

The black Amsterdam is mine, built in 2004 from the Artesania Latina kit. it is powered by a 545 motor through a pulley reduction drive, and the battery is a 6v, 10ah SLA.

The kit prop was replaced by a brass one. The yellow model belongs to Peter Barlow, a member of our club, and was built several years before mine. it is also an Artesania kit.

Our club, the Ballina RSL Club Marine Modellers, sail in a tidal salt water lake in Ballina, which is on the far north coast of NSW, Australia.
Peter Fitness.

This is BG Coulies built by Geoff Lewis. its a French Harbour tug that he built following an article in a well know magazine, advertising a set of plans, thanks to the office photocopier he saved himself several quid.

Coullies is driven by 2 550 motors driving Graupner scothell drives (not yet independantly controlled). 12v 4ah Gell battery and some roofing lead makes up the balast.

The frames are 3mm MDF with a balsa and ply skin built to 1/32 scale, the figure sat on the anchor winch used to be a German infrantry man. He recently obtained some Beccs transfers to add some more finishing touches including the french flag.

What does Coullies mean? (pronounced cooee) find a dictionary...

This is my ** version of the Sea Queen. My father owns one of the originals and when one lunch time I saw one on the ** web site I knew I had to get one.
It was to be a winter build project and work started in the autumn of 2006 and it was launched in May 2007. I was very disappointed to see the all white paint finish used on the ** advertisements and decided I was going to re-create the look of the original. Cosmetically the big problem was that the original used mahogany finish ply for the cabin sides and the ** version was just plain birch. However after a bit of staining I was quite happy with the finished colour. This was contrasted against clear coated lime wood deck planking.
Also ***a€™s bag of fittings missed out on the signature life belts so I had to make my own.

One Improvement that I did make was the inclusion of a dashboard, instrument panel and throttle slide.

The graphic on the transom was a custom cut from callie-graphics.

The supplied motor was replaced with an MFA Torpedo 850 which is a direct replacement. ( Same mount, same screw fixing centres etc ).
Battery is a 12V 7A gel cell, ESC is an Mtronics Marine Viper 40A

The hull of this model was my own design in 2004 and was sailed for 2 years, and then a new upper decks and battery system were added during the winter of 2005. The hull performed well enough but my original cabin design was too crude to keep.

The boat shown here depicts my effort to copy a 1958 ChrisCraft Cabin Cruiser at a scale of 1" = 1'.

The hull is 1/8" thick pine planks on frames with hand cut Walnut decking and 3/16" Walnut cabin sides. No epoxy or glass was used on the hull - just a good paint job.

The big change was to replace a bulky & heavy 12VDC leac acid battery with 9 AA dry cells connected in series. Bathtub testing indicated I could expect about 2 hours running time at full speed and that estimate was about right. A Dumas 12VDC motor and mechanical speed control were used with a JR XR 2 control.

The reduction in battery weight made a very large speed and appearance difference. Availability of the AA cells was an economic plus.

John called this model "Nancy Dancer". it started of with plans from 'Nexus Plans Service' for Vic Smeed's 'Vivacity'. John used the hull only plans and created everything else himself. it ended up LOA 49" with a beam of 17". With the 12VDC battery the weight came to 23 1/2#.

Because of his basic 'Sedan Cruiser' he designed all the mechanicals and electricals beneath the main cabin floor, including the battery. There was quite a bit of detail put into the main cabin - unfortunately not shown in the photos - including a galley, eating area, furniture and the helmsman's station. The scale is 1" = 1ft.

This hull is plank on frame using 1/8" pine planks. Below the waterline there's epoxy & glass and above there is just epoxy. All the brightwork, cabin housing & decks is natural Cherry with a clear urethane finish.

The power is a Dumas 12VDC motor with a mechanical speed control. The bottom photo shows that he added a 2:1 gearbox to the motor and ran it in reverse to increase the prop RPMs. He also included a constant running fan to cool the motor due to the confinement of the space.

The single propellor is 2" - 2 pitch - 3 bladed bronze. As on all his models he used a 2 channel JR XR2 75 mhz.

This was originally built circa 1960 by my Uncle, with no radio control, you set the rudder, and let it go! it was then powered by an IC engine. All the fittings, engine and electrics where removed in 1965(ish) for conversion to electric, but the project was scrapped and everything was lost.

After a number of years carrying Action-Man around the living room, it was condemned to 30 years in the loft. Restoration started 3 years ago, completed after 1 year and given back to my Father as a Xmas present.

Sadly, he never got to use it much and it's now back in my possession. After 6 months or so (see posts!) sorting a better motor/esc/battery combo, it's ready for another restoration to bring it back to former glory.

Look closely on the 3rd picture, in the background you can see Fort Perch Rock Lighthouse, a listed building which stands at the entrance to the Mersey, and the famous Liverpool Waterfront further down river. New Brighton lake is in a fabulous setting for boat enthusiasts.