Search
1,172 posts for “steam”
Page 31 of 42
Blog
HMCS Sackville
Here are a few photos of the model and the steam plant. The various fittings are coming along slowly. The dust you can see on the boiler is from a dry chemical fire extinguisher. I decided to fire up the boiler in the back yard and discover …
Blog
HMCS Sackville - WWII Corvette
… rent sized jets but it still took over 30 minutes to get up steam and by then the fuel tank was empty. I'll build a larger tank before next summer.
Harbour
SMS Komet
… & upper decks, wheelhouse, navigation and mast searchlight, Steam Master smoke module, sound module from Model Sounds Inc. (klaxon, fog horn, twin triple expansion steam engines, 8mm machine gun and 37mm canon. Two machine gunners which rot …
Harbour
(Working Vessel) Northlight Clyde Puffer
… ner smoke unit in the funnel. An electronic sound generator Steam whistle completes the 'add ons' for my Northlight. (Motor: MFA) (ESC: Viper Marine 15) (9/10).
Blog
Update #3
… on upper deck then turn it over and paint the hull. hook up steam plant radio rcvr.
Forum
Reply
Re: Boiler #3 with servos
… which works well and solved a long-standing problem of low steam pressure, the only problem being a bit on the noisy side. Plus a better gas cut-off valve from Cleveden Steam, the old one being homemade by myself. I built this in the 1970s …
Blog
Deck planking
Steaming the edge planks The Bow has a significant curve and needs a plank /piece of timber to follow the hull curve for a width of 8mm around the total circumference of the boat. Others have cut a shaped piece from a sheet of wood but this …
Forum
Reply
Re: Marian Belle' Tug Mobile Marine Kit.
… another Mountfleet kit Danny Boy a North sea Drifter, with steam plant which was difficult to fit as small narrow superstructure.
Harbour
Marian Belle' Tug Mobile Marine Kit.
A Mobile Marine tug kit, modified to take a steam plant, TVR1A-BB steam engine, 3 1/2" diameter x 6" length boiler. 4 channel for forward / reverse. speed control, steering and gas cutoff valve. Around 2 years to complete.
Blog
Boiler #3 with servos
… w piping in set up to install the servos for the shutoff to steam.Had previously installed the rudder servo and engine servo and tested them out.The shutoff servo proved to be stubborn as I didn't realize it had shorted out needed to find a …
Forum
Gorleston Model Boat Club
… e a few regulars down the pond most Sundays. Even had a new steam boat this week! Most of us are still in hiding though. I'll be glad when we get back to the 'old' normal
Blog
Change
… oiler I found that I needed to use the valve to control the steam better.The servo for the foreword/reverse works well but will be better at full each way when running.I will use the shutoff to slow the engine down. Now the change I had ano …
Blog
New top end of Zulu
… tice two chimneys, one for the cook stove, the other from a steam boiler to power the steam capstan. Fishermen it seems were keen to adopt modern technology where it reduced hard labour in fishing net retrieval. One issue I have with this m …
Blog
Silver soldered
… ed to silver solder all the pipe work.The next step will to steam the boiler to check all piping and run the engine under steam . Rick
Forum
Esc motor pairing.
Nerys, steam power is out of the question, as its quite a slim Hull. So it will be twin motors with individual driving paddle wheels. Although the plan shows single drive. Cheers Colin.
Blog
planking
And so it starts shaping, sanding, steaming, gluing.
Blog
Fitting the side skins.
… at along with a light spray of water which quickly turns to steam but allows the ply to become pliable this is then bent around the bow and clamped, I now leave this overnight to dry and cool, which will hopefully retain the bend. I then dr …
Blog
Fitting the balsa block
… lsa is also soft in places and harder in others (I wish I’d steamed the ply) making sanding difficult. Solution – use the wood hardener on the block, this helped and eventually I had what I was happy with using a template traced from the ke …
Blog
Fitting the bottom skins
… odate the prop shaft curve. The bottom skin also needs some steaming to fit the curve just before the balsa block, this curve is at the discretion of the builder so a gentle filing against a pre-made template to ensure both sides are the sa …
Forum
SEA COMANDER RE-FURB.
… between the carpark and the boat club. The Model Engineers steam track runs around and across the dams and is nearly 2k's long So we have a great drawcard!
Blog
Arctic Convoy
… omething else onto the slips ,decided on a cargoship /tramp steamer from the 30s-40s will call it Arctic Convoy as a tribute to the gallant men who endured so much. Started with the main decks and boat deck that I can do in the warmth of th …
Forum
Nostalgia
An ad for a steam set from 1979 - love the price - could afford one or two of those !
Blog
Maiden...and a minor !!??**+! Setback
… aside, if I can’t fix it...well, I think she’ll make a fine steam launch, cat rigged sailing skiff or maybe fit her with an outboard. I have options, and I’m all kinds of stubborn..
Blog
Servo
… t the engine to run both ways. On air it runs very well but steam testing will be the real test. Also a picture of the rudder in place will need to get the rudder servo in next. Rick
Harbour
(Other) Wild Rose
Wild Rose was originally a steam launch with Pelican V twin and home built vertical fire tube boiler. She is now converted to electric and has the addition of a smart striped awning. I designed the hull with a program called ply Boats years …
Blog
Cabin Coming Along Nicely
… rved Cover. The front of the wheelhouse is in the vegetable steamer ( my wife is out for a few hours, he he he) and will try my luck at bending it to shape on the plan. Right wrong or indifferent, I have used 1/8” medium hard balsa for this …
Blog
Deck Winch.
… appened to visit Beamish museum. Low and behold there was a steam driven winch just lying on the ground. This gave me some idea of what a steam driven winch looked like. Made from plasti card, some gear wheels, brass wire, etc. Very happy w …
Blog
HARTLEY FLARELINE, NEW PROJECT
… g paper under to protect the plan/drawing when gluing. I've steamed the ply cabin tops over the kettle and pre bent them to avoid putting too much down force on the structure when 'roofing'.