Our July, 2016 Fun Float was a great success! The weather was perfect and we had a great number of spectators, met a few new Captains who just came to sail with us and see what we are about! We had up to 6 scale sail boats on the water and several powered boats. We were also experimenting with "on board video" which we are setting to music and commentary. Even the wives enjoyed the day of great weather, a snack bar, walking trails and each others company. There was even talk about relocating our regatta to the "Muddy Run" location.
Now that I done skegness lifeboat day I can get on to finish what needs to be done & hopefully before Xmas I can have her on the water,the crew at skegness loved the model as a whole and even the mayor of skegness liked it,but now time to get down to the nitty gritty and get her ready for the water.
Sunday sailing and a chit chat down at NorthWest Scale Model Boat Club,Squirrel Lane,Horwich,Lancs.Thought I'd put on my first video,just myself and husband watching a couple of the guys on a pleasant Sunday afternoon.
My Monster Mersey,couple of photo's from a show in Newark
Photo 1 : She is quite big(talus is on a smaller table)
Photo 2 : She makes the other boats look quite small
Photo 3 : The proud owner of the Monster Mersey is next to the stig in the dark blue top
Not known when I got it she was a wreck,and I am still refurbishing her,I was told that it was in a garden for over 4 1/2 yrs uncovered in Scotland so I set about bringing her back to near on original state she was first in
That's an excellent running time for a fast model.
😀
It gives a great indication of what can be achieved with brushless motors.,
I'll have to try brushless motors in some of my fast scale boats. I only have one brushless powered model at present, this being the Proboat Blackjack 29 fast electric.
Not known,but he knows and congratulated me at a show for putting the talus back to how it was,he is on another site in which I have put photo images on and he likes what he see's
One Twelfth Scale Speedline Severn Lifeboat try out
Having installed the running gear I just had to try it out. The boat is about half the weight it should be so ballast is something I will have to add. But lots more to do yet
Hi figtree7nts,
The reason it can pivot pretty much in its own length is because it is fitted with a bow thruster.
In this case it's a Raboesch model
The two main motors are Emax BL4030 brushless motors running with Hobbyking 90 amp escs. I power these with two 5 cell lipos batteries in parallel.
The Raboesch bow thruster has a brushed motor rated at 7.2 volts and this runs through an esc for brushed motors. (I was lucky to have one ready after I converted one of my boats to a brushless motor). I power the bow thruster with a 7.2 volts nimh battery pack again left over after going to brushless and lipo batteries.
Les
Hi Les, fantastic job on your lifeboat! I'm thinking I'd like to build a pilot boat, maybe the one from aeronaut. as long as the model is made of plastic I'm good anything else and I'm lost! hope you don't mind but I think I'll put a bow thruster in mine also.
Here's the photos of the cord coming through the middle of the crane, connected to the sail winch on the bottom end. The bracket to get it to go round 90 degrees had to be modified as it started jamming with no weight on the hook, now a piece of bent tube cut in half as a channel.
Finished my first boiler with home made engine and reversing valve small leak on main steam valve still to cure but other than that all is well. Am I a happy bunny!
just got to fit it in boat and its off to the pond
Roger
Crane story part 3! Now that the jib raised and lowered, I had to tackle rotating the turret. I canibilsed a radar setup I'd made (again from helicopter parts after a crash!) to rotate the turret. Video of the radar motor in operation shown.
Crane story continued.. once the swash plate was connected via servo arms to the jib, I had to develop an arm to control them from a servo - pics attached. Once the bracket was attached to the servo, it allowed the jib to move up and down, whilst the turret rotated. I then had to work out how to rotate the turret! More photos to follow..
As the turret is mounted on a hollow tube, this allows the cord to run through the middle of the crane, over the jib and down to the hook, and on the other end, attached to a sail winch so that the hook can be raised and lowered. Will add pics in a sec.
