Billing boats, which took me 3 years to build.Hull was planked and theh fibre glass. Boat has full functional remote with seperate port starboard control,rudder and bow thruster. full inside and mast lighting.
Zoom 1 (Interceptor) Mono boat.
Built from a Glassfibre hull, brought on Ebay for £35 the hull is a slim mono racing type with a self-righting side cabin it runs a 1400W 14V 2958 4200KV Brushless Motor and 29-S Water Cooling Jacket with additional air cooling fan.
I did not want to use a flexi drive as high maintenance and prone to failure so the shaft runs via two universal joint one at each end. the propeller is a 38mm copper alloy
The ESC is a 200W and water cooled the twin rudders supply separate water one for the motor and one for the ESC.
The rudder are positioned to reduce prop-walk and are hinged to prevent damage if you hit a object in the water and also for ride adjustment.
Turn fins and trim tabs for ride adjustment were provided by a spares kit for another boat. also foamed and added an inner sealed hatch, a rubber bump strip and safety loop.
It certainly looks like we are having notification problems again, First it was very few getting through and now we get 14 YES that is fourteen of the same.
A favourite model boat there must have been hundreds if not thousands made.
When I brought mine there was a choice between two sizes 36in (90cm) or 48in (120cm) and then you could choose between a wooden hull or a fibreglass hull. I went for the smaller boat with the fibreglass hull. this was back in the 1980s.
Background of the boat
The boats Perkasa class consisted of three motor torpedo boats built by Vosper (UK) for the Malaysian Navy as follows:-
Perkasa 150
Penula 151
Handalan 152
This model has 3 motors, port & starboard are Graupner 600s and one 700 type in the centre runs 3 ESCs front and rear guns operate via servos, with flashing LEDs down the barrels.
Greetings from Germany! I've been out of the net for a while and rebuilding this boat with a totally new superstructure, paint job and electronics. I obtained the fiberglass hull measuring 24.5 X 9 inches from a California fellow via E-bay. Formerly a 45-footer Chris Craft at 1:24 scale, this updated vessel was inspired on a 1970s 30-footer Chris Craft Tournament Fisherman and on 1970s 28 and 33-footer Bertram boats. 😁 The Chris Craft in the attached picture from an early days brochure was the very only Chris Craft utilizing a Deep-Vee hull. The story goes that they apparently copied their boat following the lines of a Bertram 28 based on famed boat designer Ray Hunt. Bertram sued in court and Chris Craft ended up building less than 200 boats of this type. After all, the Chris Craft vessel ended up being better than the Bertram in terms of cabin space and overall value. Highly cherished within the American sports fishing community, many of these boats are still up and running.
This truly stunning piece was created by Barry Sharman of Southampton international Plastic Modellers’ Society (IPMS UK). A replica of the HMCS Agassiz with a mind boggling level of detail not only on the outside but also on the inside visible through cut out sections of the hull. Barry invited me to see the other side of the model and was amazed to see several crew members restoring that side. Spectacular and no wonder it was protected by a glass case that Barry kindly removed so I could film it without chance of picking up any reflections.
Absolutely, Modelling par excellence👍
Just think of the planning that must have gone into this! Building such detail deck for deck from the keel up 😲 Never mind the superb weathering, just back from several N Atlantic crossings!?
And where the heck did he get all the interior detail from ?????
Fabulous, just great shame that she'll never float 🤔
Just fresh off the shipyard, this is my version of an American made Uniflite (firm died several years ago) "Salty Dog" 28. its name is a Puerto Rican slang for escapade. From the same firm who designed and made the legendary Vietnam War Patrol River Boat (PBR), this boat was part of Uniflite's recreational boats line. For this one, I utilized a fibreglass hull I found on Ebay and did the rest with Ethylene 2mm plastic sheets. it runs a 9.6v NiHm battery, a 30A Mtroniks controller, a 3-bladed 35mm M4 bronze propeller.
Scratchbuilt WW2 1/24 Scale Vosper 73' Type 1 MTB. Built in 2016, in company with a friend's 1/24 scale BPB MGB.
The Vosper hull is built from balsawood and fibreglass. The upper deck and superstructure is from balsawood. The weapons and fittings are from brass, aluminium and plastic. The 20mm and gunner can rotate.
So glad to have this scrollsaw in the shop which has made cutting the bottom boards a very easy task. I cut the chines from Ash using this saw too with a fine blade. Look closely and there is a plexiglass cover on the table to give me a zero clearance around the blade hole, thus keeping small parts from falling under the table. A shop vac is attached to draw away the fine dust that this machine produces. My lungs are greatful too.🤓
ON THE WAYS: 1:48 SCALE USCG 140' BAY CLASS ICEBREAKING TUG; FIBERGLASS HULL WITH WOODEN CABIN/SUPERSTRUCTURE KIT FROM COAST GUARD MODELS IN CHICAGOLAND. WILL BE REPRESENTING ONE OF THE CUTTERS I SAILED ABOARD IN THE EARLY '80s.
USCGC KATMAI BAY (WTGB-101), H/P SAULT STE. MARIE, MI, USA.
Both Fairmile D boats 1/24 scale and are scratch built. They have both been about 6 years in operation.
MGB623 is an MGB, flying the Norwegian flag and belongs to a good friend.
Mine is MTB741. it is powered by 2 Graupner Speed 700 12V motors with NiMH batteries. The 6 pdrs and 20mm guns can rotate. it has a balsa planked hull and fibreglass skin. Decks and superstructure are also balsa. Guns are from tinplate and brass.
Excellent boats with great scale performance. I like the Fairmile Ds as they are good subjects for modelling and at static displays they always attract a lot of attention.
Hi. Just put this back together after the 3rd brushless motor caught fire. Made from a rejected glass fibre hull which I bought cheap at a show. I have now learned how to do glass fibre repairs.
Hi, thanks for the info👍 I'm new to BLs, but learning fast, and your experience confirms my growing suspicions that outrunners not only deliver more torque than inrunners (size for size) but that they are also more reliable and seldom need water cooling.
Your new motor seems to be a larger diameter 58mm?, as opposed to 31mm for the old one, so I begin to wonder if the old ones were simply overloaded by a big prop causing them to draw more and more current and hence cook! 😡😭
Check out this test drive (Italian)of your new type motor!!
cheers Doug 😎
PS Caption says that with more than 3/4 throttle the boat becomes unstable! Then it flips 🤔
PS Don't worry about 'adding up' the Watts and Amps!
True the spec says 12.6v and 35A, which theoretically gives 441W.
And the power is rated at 220W. This simply indicates to me that the motor scoffs 441W of power (at Max ratings) and spits 220W out again, i.e. ~50% efficiency 🤔
Almost any decent brushed motor will beat that! But with other penalties😉
Cheers Doug 😎
