HI shipmates, here,s a few shpts of the "Port ".
She,s a 1/80 scale scratch built cargo ship of the Port line company from around the 1950,
A ship this size requieres quite a bit of balast, I use water, it takes around 40 lds to get her sitting right, this is pumped in and out with a submersible caravan water pump.
Most of the fittings are resin castings.
there are a few more bits to finnish off but could not resist the chance to try her out on the Chasewater pool.

my boat is powered by a 26cc zenoah engine,I skinned the outside in real carbon fiber and the interior with carbon/kevlar.I use a spektrum DX3S 2.4ghz tx with a spektrum MR3000 marine rx.the boat is equipped with a killer bee remote kill switch that doesn't need any power source to work so it will still kill the engine instantly in the event of battery failure or broken wire or when I want to from the tx. the carbon fiber was hand laid and wetted out with a special resin,then around six weeks of hand sanding with different grades of wet and dry to get it super smooth,then polish.

HI Fellow enthusiasts
The first photo shows the boat as it was bought from an E Bay auction in late February for the price of 14.50, for that price I had to bid on it, even thought I had a new kit of the same model on order from a model shop from the end of December, before VAT went up. The models turned out to be the 4 feet versions some 11 inch wide and now is about 19 inch high. This model turned up several days before the new kit turned up, and was a bit worse for ware than anticipated as the deck had started to part company from the hull. After stripping the deck of all remaining deck furniture the deck was re laminated to the hull, prop shafts and rudder tubes also refitted using plenty of resin and cloth. A rubbing strip was fitted around the deck hull line to tidy up the visible damage. When I was happy with repairs the hull and deck was rubbed down and sprayed. Using the information in the new kit and some photos of actual boats, MJB's (My junk boxes) supplied all the required parts to scratch build 90% of the models fittings as seen, this includes the figures on the deck. These being obtained off an EBay site as 1/24 unpainted train scene figures that required some or may be a lot of adjustments to their appearance. Several items have still to be made and fitted. As I'm working on her sister boat P147, will make extra parts in one go.
The boat has twin electric drives, the motors, MFA 919D series, are fitted with their own 2.5/1 gearboxes and they drive 40 mm three bladed conta rotating brass props. They have independent 15 amp Electonize speed controllers run from two 7.2 volt packs in series. The switching arrangements for lighting has still to be finished off. Don't know if I'll fit a sound system as the boat is for my grandson.
The boat has had several trips on the Society's water at Cwmbran with myself and my grandson at the helm. it seems to go fast enough for him. (The new boat P147 has been built with triple screws.) Can't wait to see both models on the water together.
Hope you have enjoyed the pictures and information.
Regards
GreyWolf

bought this 50inch hull off ebay and thought I would try a make a boat just with my own idears and this is how it turned out,powered by a 720bb motor,12inch propshaft and a 60mm 3 blade brass propellor.all built from odd bits of wood in my shed. installed wood in bottom and then filled with a two part epoxy resin

This is my second attempt at scratch building using a a grp hull. My first boat was an MTB/MGB built on a Perkasa hull as a semi-scale model. (see All things Rc - Power setups).
This time I have concentrated on keeping things lighter but it still weighs in at 2.5kg!
I have built without plans, relying on internet photos scaled etc using "Photo deluxe" and "Photo Express".
Virtually everything is built from plasticard apart from a 3mm liteply deck.
The dinghy is epoxy resin and microballoons, ths scramble nets are Lego!
Power is again courtesy of Graupner -2, Speed 600 8.4v using lh. and r.h 35mm props. Esc is one of those 50amp ones from the far east. These are far cheaper than the Viper Marine 40 used in my MGB, but slightly heavier and less sensitive at low speeds. Current drain (in the bath!) is up to 30A but this gives a superb on the water pace of an, estimated,8mph. Battery is a 4,600 mAhr NiMh.
(A true scale speed approaching 150mph plus).
I sail it on Ullswater in the Lake district and the Vosper Perkasa type hull shape is superb in the real waves that we get there, flying over the crests and taking aboard No water!
It really looks the part as my photos would show if I could learn how to load more than one! Can anybody help with this?

Scoter was built from a Dumas kit ordered from America. it is a planked hard-chine boat reperesenting an East Coast fishing cruiser, She is 2 feet long with a Graupner Speed 500 motor running on 7.2 volts through an MTroniks 10A ESC. The crew are from George Turner Models, 1:12 scale resin figures.

Please see my previous post for the story so far. Photo 1 shows my Lifeboat with its first paintjob and on its first sea trial on King Lear's lake, Watermead Country Park, Leicestershire. Photo 2 shows the boat with its completed paintjob and handrails having been fitted bought from Speedline models which are made of pewter so can be straightened it accidently bent. Photo 3 shows my Lifeboat on its first official outing at the Midlands Model Lifeboat Show at Dudley in May 2008. My crew have now been added also bought from Speedline Models 1/12th scale as they are the best quality resin cast figures I have seen. Strictly speaking they are too moderned dressed but I like the quality so I decided to fit them. The last photo shows it loving the rough seas again at King Lear's Lake at times having 10 to 12 inch waves.
Marie (alias Mrs Froggyt996)

Here is a video of our boat (Vigilant star) sailing at New Brighton boat lake on the wirral every Wednesday.

The boat is a semiscale (Coast Guard Cutter), designed by Hal-Harrison in Marine Modelling. I have doubled its size and put two 540/1 Mfa motors in, driving quanta 45mm props. She is 36" length 8" Bow, runs of one 12 volt 7Ah SLA battery.

It is made from Balsa/Fibreglass resin. Runs well no leaks to date. Gerry.

Some 25 to 30 years ago I wrote to Peter Dimberlins for details of the Crash Boat following a mention of him in 'Model Boats '. Peter supplied me with data and we have been so close ever since. These and more Images are of Peter at the helm of my Steam boat' Lady Halina ' and his successfully (ha ha) steering my Crash Boat as I did not know it was so fast/ ballistic. More pictures to follow of this gracious man at the helm at our pond/ tidal creek during his momentus visit to OZ in early 2008. My model is some 30 years young and is with the third engine as the others were worn out with use ( OS35, ENYA35 now a S/C 40 a bit too much) in a 25 pound plus model, yes she is heavy. She has been re done over and over(paint resin paint resin etc) and only had the 1/8 inch steel prop shaft (yes 1/8) replaced recently. I have a "leather flange coupling"as on all my power boats and never let me down and vibration free. Exhaust system 1:muffler to a 2.tar lined tin can to a 3.small resonator (equals quiet ) More to come of my Crash Boat as a result of this gracious man and his service to modelling even to a colonial.

Z15 "Erich Steinbrink"

A german WW2 Destroyer was a Ted Radestock Semi-Kit.

She took just over 2 yrs to build in total, but did include a house move in between!!

She is built as per the kit with the exception of James Lane guardrails and modified Deans funnels as the original resin funnels were very heavy.

She is powered by 2 Deans motors, 35mm props and the batteries are 2 x 7.2 volt 2 Ah NiCad packs.