this is my boat built from the aerokits plans. she is the 46 inch version, power is from a brushless motor and lipo set up. sailing trials over easter hols weather permitting!

Bought off ebay, where else! Had been started as a cruiser, with one very small electric motor,then put in a loft for goodness knows how many years.Replaced prop shaft with 2, 40mm r/h and l/h props, 2x 540 motors running through 40a esc.Radio is 27mhz. 2ch. would like to swap to 2ghz to get rid of the unsightly aerial! I am awaiting some plasticard windows to Improve the looks and will slowly add fittings as and when.I tend to sail it every now and again on the boating lake in BUXTON, no-one has shouted as yet,though I'm not sure the swans approve.!: The photo on the water was just as the power was running down, none as yet at speed.It is very manoeverable with the twin rudders,almost on the gunwhales at speed.

This is an Arowana 22.2" mono EP hull, allegedly self righting, however, on it's maiden run I turned it too fast and flipped it, sadly the self righting didn't, and a hatch clip failed, the end result was that after about 40 seconds of being upside down, the back end dissapeared, and it ended up 70% submerged with about 6" of bow pointing towards the sky. I have since had a play in the bath, and cannot get it to self right, also it leaks water from the factory fitted divider for the flood chamber, so not the quality that I thought it was, don't quite know how to rectify that one.

This is a lighter version of my MK1 previously posted, lighter by some 80g, and having a slightly larger prop, I assumed it would be faster, the reality was that the X438 was too much, so will go back to an X435. it ran a bit wet as well, so now I have adjusted the angle of attack on the prop, which should sort things out. The 6 inches of boat tip in the pond was my Arowana 22.5" mono, it flipped and a hatch clip failed, and that was the end result, so I was trying to nudge it in, and I failed, luckily my brother is good with a fishing rod and recovered it.

Graupner Systems Catamaran (Second hand, and refitted) with Leopard 2860 5050kv Motor, it has 2 x 11.1v 4200mAh 50c-100c batteries in parallel, as the motor has a max draw of 120A, The prop is an octura X435 connected to a Prestwich models Strudder.
This was it's Second run, , this run was very successful, the speed took me a little by surprise, hence the expletive (Sorry). I would love to know the actual speed. After a short run, a connection on the electrics came adrift. all repaired and ready to run again now.

Graupner Systems Catamaran (Second hand, and refitted) with Leopard 2860 5050kv Motor, it has 2 x 11.1v 4200mAh 50c-100c batteries in parallel, as the motor has a max draw of 120A, The prop is an octura X435 connected to a Prestwich models Strudder.
This was it's maiden run, and initially I hit the throttle too hard, and made it tail walk. and the coupling came adrift. after a little tighten up, the second run was very successful.

Hi" All . Thought I would put some photos of my last winter project for all to see ! This model took approx 3 month to rebuild from an ebay wreck . A 1980s lesro Stiletto speed boat kit.A total rebuild was needed . Siletto running set up is a Johnston air cooled speed 600 electric motor. 50 amp speed contoller 7.2 volt at4600mh power pack which will lift her out of the water at very good speed. Siletto is finished of in dark mahogany stripwood vinneer & Ivery white / post box red .I do think the older colours look better on the older models . I sail my boats at Sheringham Norfolk
enjoy the photos . From A prestney

This is identical to the MK1 version, but 80g lighter, in a bid to get more speed, just need to find a way to record the speed

Scratch built outrigger hydro with a 3600KV motor ESC and a 11.1v 45C 5000mAh battery, running an Octura X435 prop

HI shipmates, here,s a few shpts of the "Port ".
She,s a 1/80 scale scratch built cargo ship of the Port line company from around the 1950,
A ship this size requieres quite a bit of balast, I use water, it takes around 40 lds to get her sitting right, this is pumped in and out with a submersible caravan water pump.
Most of the fittings are resin castings.
there are a few more bits to finnish off but could not resist the chance to try her out on the Chasewater pool.

Built from a .PDF plan I found on the net, this 22" Outrigger Hydro sports a Hobbywing 3600Kv Brushless, along with a Hobbywing 60A esc, a 5000mAh 11.1v 45C LiPo, and an Octura X435 Prop connected to a Strudder from Prestwich models.. it weighs 930g without the battery, with the battery, she goes 1386g.
This was it's Maiden run, at Herbert Woods Boatyard, at Potter Heigham Norfolk. it ran very nicely, but can do with a little tweaking to get more speed.
For the record, I did not swear, it was someone onlooking.

Built from a .PDF plan I found on the net, this 22" Outrigger Hydro sports a Hobbywing 3600Kv Brushless, along with a Hobbywing 60A esc, a 5000mAh 11.1v 45C LiPo, and an Octura X435 Prop connected to a Struuder from Prestwich models.. it weighs 930g without the battery, with the battery, she goes 1386g.