here are my three boats, oakgarth 42" twin screw 4 blade props with kort nozzles she also has a working bow thruster.She running two speed controllers off a 12volt sla battery and has full working lights I would love to say I built her but I never, all I have done is added lights and give her a full makeover. Next is Doug the26" pusher tug twin screw 3 blade props full working lights and water jet single speed controller futaba radio set up I have just changed the crane on this again I have only done cosmetics to this tug and my last boat is a 20" seaport tug this is what my grandchildren sail and for 60 quid its great thay love it .the paddling pool was 15 quid for argos and perfect for testing well better than filling the bath .

Built from a Traplet plan 2012, all wood construction with plank- on-frame hull. 385 direct drive motor with 3 blade prop, Mtronics 10amp speed controller and 8x AA 1600m/a batteries wired in parallel.

Built from a Traplet plan in 2013. All wood construction, JP 400 direct drive motor with 2 blade prop. 2x 3.7amp 7.2 volt NiMhd batteries wire in parallel and a Mtronics marine 15amp speed controller.

This tug was made from a Tito NerI tug kit and modified to make it look more like one of the local tugs near my home, she is fitted with two azimuthing propellor units driven by 900 size motors and a bow thruster unit

HI this was my winter project the hull was given to me by my son who got it at a car boot sale it had been on fire as it was driven by a petrol engine in now has twin brushless motors with 45mm props but going to put 50mm props on when they come as it needs a little bit more speed Built from a set of plans this my first go at this as I build from kits in the past cabins made out of 3mm/1.5m ply and some 1.5mm balsa wood . Hull was sprayed and the deck and cabins brushed with enamel paint.

This model of the tourist attraction in Liverpool a few years ago.Sadly after a couple of mishaps all four have been withdrawn from service. The model however survives. it was scratch built from photos and site visits by myself (Max Ferrie).There were no plans available. it is about 28inches long and roughly 1/12 scale.It was built almost entirely from plywood. As you will see from video it operates on land and water. it is six wheel drive using differentials on all wheels. When in water it is prop drive. it has two small electric motors for power, the wheel drive being very low gearing (too low really it goes very slow on ground). it was completed in 2010, and is filmed sailing at the portable pond at Toys For Boys in Waterloo in 2010. it has sailed at Hoylake MBC also.
It is powered by two 6volt 4AH batteries in series to give 12volts.

twin speed 400s driving stock (kit) props off 1 6 cell NiCad. Speed is "moderate scale"

💀 Hello friends, I am sharing a kit that sells here in Brazil. This is a fishing boat, a motor included in the kit 380 brushed, propeller shaft, pipes, all made of balsa. To put my touch to the lighting, did the radio antenna, put some flags. Detail is left with the box of fish that are rice painted with spray paint aluminum.

Single 550 Brushed Motor and Reversible ESC, 2S LiPo, 2.4GHz Radio System, Turnigy Blue Prop, 2 x 9G servos for rudder and lights.

Functional Nav Lights and wailing siren.

OA Length 690 mm, Beam 180 mm, AUW 1656 grams.

Following the legendary Keil Kraft Eezebilt plans for a Mermaid Ocean going boat. Plans exploded to 200%. Trying to build it completely out of Plywood and Foam Board.

OA Length 710 mm, Beam 180 mm. AUW 1.98Kgs.

She carries the name 'JAYSHIL". it is a portmanteau derived from the names of my late parents.

Model features working lights as prescribed by the international Maritime Authorities:

http://www.bosunsmate.org/seamanship/lights.php

In keeping with Rules 22 and 23:

http://www.bosunsmate.org/seamanship/rulesoftheroad.php#rule23

Brushed 550 motor, Reversible ESC, 2S LiPo, Turnigy Blue Prop, Working Lights and indigenous Sound Generator unit.

Video is available here: (you may need to turn down the volume a bit as the horn is rather loud)

I would welcome any queries and/or comments on this build.

Thanks and Regards,

VC

I have just acquired a part built original kit. I will be restoring this to its full potential in due course but am sharing the pics for now. I will post as a build blog.
Condition is good and the build seems to be to a good standard. I intend to replace the single proptube with a double and use a couple of brushless motors. 👍

Sometime around 1968 I found a small set of drawings, about A4 size, for Sct. Knud in (I think) Ships Monthly. So I enlarged to 1:32 scale and made my model plank-on-frame with GRP overcoat. She is powered by a 6V Pittman motor driving a self-made scale prop and 2:1 gearbox. Steering is effected via chain and quadrant as per prototype! Everything bar the anchor, anchor chains and steering chains is self-made using a variety of materials (brass, plastics, 'Perspex', and copper electro-deposited cowl vents). Recently I fitted her out with LED lights: interior, navigation and working. One might notice that I abhor a working boat looking like "Daddy's yacht" and so I apply custom dings, stains, oil spills, scratches, wear and tear to my tugboats 😀 My Knud runs as well today as she did 45 years ago and in all that time has only needed one repair to her gearbox!