Search
1,869 posts for “brushless” · in Forum
Page 58 of 67
Forum
Palm beach
… e. As a fast speed boat it would really perform best with a brushless and LiPo. As you already have brushless ESCs this would seem to be your best option. If you are not using LiPos at present then you could use NiMhs whilst you experiment. …
Forum
Palm beach
… out spending a lot of money on an experiment. Or I could go brushless, I have plenty of large controllers for those. Any ideas would be welcome. Thanks
Forum
interference suppressors on electric motoers
… rushed motors but all brushed motors generate interference. Brushless motors do not and must not have capacitors added to their leads. Keep all dirty (high current) wiring well away from the aerial, rx and servos and try and route servo lea …
Forum
ESC problems
… ventually bought all new gear. So I now have a 160 Amp ESC, brushless motor and LiPo batteries. The 48" Perkasa runs like a dream. https://www.youtube.com/watch?v=s9Y850Y_o1w Not sure if the hyper link works. Noise from out of balance prop …
Forum
Poor run time
I have the Sea Queen which has a Jp C50-20 brushless motor. I use a 12v lead acid battery as power supply. The battery powers the motor and the steering servo. My issue is that when fully charged the boat gets up goes very well,however afte …
Forum
Poor run time
… hard I agree with Flack. The SLA is not a good choice for a brushless motor. Basically the motor is a low resistance device that needs a low resistance power supply. SLA's have a realtively high internal resistance which limits the current …
Forum
Poor run time
… east favourable power supply for a 46 inch Sea Queen with a brushless motor, brushless motors tend to want to draw their power faster than a lead acid battery can give it which could account for the slow speed whilst the battery is still sh …
Forum
236674
Hi, The motors are turnigy aquastar 3660-1460KV watercooled brushless motors x2 The esc's Hobby King 90a Boat esc 4A SBEC water cooled. Batteries Turnigy 4000mAH 3S 20C Lipos. Bow Thruster Raboesch 108-01. Do you recommend a Mixer.
Forum
236674
"Hi, I have water cooled brushless motors & esc's plus lipos, my TX has 6 chanels." I am guessing that water cooled brushless motors are inrunners. While they could be used your going to have to be very careful in the choice of props. I sho …
Forum
236674
… t the Action Electronics diagram as its not appropriate for brushless motors. Your brushless motor will have three wires coming off it, The speed controller will have three wires coming off one side and two wires coming off the other side c …
Forum
236674
Iam using water cooled brushless motors and esc's plus lipos.
Forum
236674
… sing brushed motors, a lot of the stuff will be no use with brushless motors. Shaun
Forum
236674
brushed or brushless, how many motors, lights, anything else ? How many functions ( channels) on your TX?
Forum
apprentice
Brushed or brushless? How many Escs? Tx/rx set? Easier to offer help if we know this info. dave
Forum
Veron Huntsman 28
… 1 channel to 2 ESCs but 2 motors NEED 2 ESCs when you have brushless no way out of it sorry. The 30 combo will have more than enough grunt and with the ability to drive 30A through a motor means that your ESC will survive your playing with …
Forum
Veron Huntsman 28
… am used to and does mean I can steer just using the motors. Brushless seem to be quite well matched so if you use the same types of motor and esc with the same settings I would expect the speed to each prop to keep in step. I also have a Ta …
Forum
Veron Huntsman 28
… it is truly superb. It is not possible to use one Esc with brushless as the motors provide feedback to the esc to control the speed. Sorry you will need two. Giant Cod used to have a range of suitable kit but Google will provide a host of …
Forum
Veron Huntsman 28
… sman 42 is 42" long, I have been looking at Tornado Thumper brushless motors as they get a very good write up, probably using 2 x 14.8 lipos and one speed controller for both motors. I have a Futaba 6EX that I can use as you do! I have used …
Forum
Veron Huntsman 28
… tle control on your Tx. My 34" crash tender has one 28 size brushless and with 11.1v Lipo (2200mA) is quite uncontrollable without this. I use a Futaba 6Ex Tx which allows me to adjust the throttle stick output to about 45% in my case and I …
Forum
Veron Huntsman 28
… these systems http://www.cornwallmodelboats.co.uk/acatalog/Brushless_Motors_Other.html at only 28 inch the smaller of the 3 would be more than powerful enough. Remove the red receiver lead from one of the ESC so only one BEC is in use. and …
Forum
Help needed
… electrics and RC. I have a planet T transmitter and recover,brushless motor.help
Forum
Help needed
Not sure if that brushless motor will be big enough, hard to tell from the photo, but if it isn't they are easily swapped. If you are really struggling with the electrics, get all the gear together and bring it down to me in Dalton in Furne …
Forum
Help needed
I may be wrong but looking at your picture you have a brushless motor ( 3 leads) and a brushed esc ( 2 leads out). if that is correct the 2 don't mix. A brushless motor requires a brushless controller. The brushless motor works differently.
Forum
newbie boat id question
The Speedline CR1700 is powered but a 1700kv outrunner brushless motor fed from Lipo 3cell battery and a Fusion Hawk 50amp ESC. additional buoyancy was fitted in case of accidents. With that set up the performance is terrific and very stabl …
Forum
newbie boat id question
… ify what I uave bought and if it would be possible to run a brushless setup in it? Regards Neil
Forum
newbie boat id question
… ture shows a Speedline CR1700 model that is supplied with a brushless motor and all the required parts except the battery and radio. I have built one and it performs exceptionally well.The kit costs £99 from Speedline models
Forum
newbie boat id question
… ctures and dimensions would be a good starting point. As to brushless motors the short answer is yes you can put a brushless into anything that a brushed motor could be used. Brushless motors come in a VAST range of sizes and power outputs …
Forum
1/16 areokits crash tender
… ponses - both confirmed my suspicions as I am converting to brushless motor - so will reduce prop angle down to about 10 deg with suitable clearance for propeller. Also appreciate the motor setup detail suggestions as I am new to this are o …