Search
845 posts for “hull paint” · in Blogs
Page 28 of 31
Blog
DAMEN STAN 4207
Removed all the internal components and wiring, then painted the inside of the hull with a light grey paint. The upper hull was sheathed with 1mm ply from the spray rail to the deck. The construction adhesive used to reinforce the bottom sh …
Blog
Boat stand
… perstructure now I'm going to need something to support the hull securely so it's time to build a stand. To get the profile of the hull I used a couple of wire coat hangers, the sort you get from the dry cleaners, and carefully bent and for …
Blog
Fitting the bottom skins.
The skinning of the hull is probably the hardest part of the assembly as it involves careful trimming and shaping to ensure a good fit without resorting to fillers for making good. The skins can be bent quite successfully with the applicati …
Blog
DAMEN STAN 4207
… firmed this. Transferred the dimensions and layout into the hull and installed the sterngate frame. This moves correctly as the servo is stroked. Could have now moved to sheath the outside of the hull and fit the deck. Decided it would be b …
Blog
Muddys Tarpon
… x.. Mesmerized is probably the correct word, because of the hull lines, hull dimensions and the radio control, "Bang Bang" rudder control and a Diesel engine for it's power. Perhaps the fact that it covered our small pond in a very small ti …
Blog
fairey huntsman 31
… water. i got bored with the colour so i rubbed her down and painted the side of the cabin a dark blue which acutlly was the same colour as my car and the tops of the cabins and hull white, i re-covered the seat cushions with red leather and …
Blog
San Pedro Push Boat
… edro needed it's waterline so I put one, especially since I painted the hull brown. So I put the waterline because she just didn't look right with out one!
Blog
San Pedro Push Boat
Having started painting the hull the deck and push pads, I've discovered a breach in the hull that's about 130cm X about 1cm or so! I'm hoping when I reglue the seam it takes, I'm not sure what to expect next.
Blog
Monster Mersey
… see it rot away so I decided to take it on.I am now on the hull,it's been rubbed down and ready for paint then I can put it on the carriage and start from deck upwards
Blog
Tugboat Serenity
I've glued the Hull together and have also used Bondo to the Keel, having done that I also sanded it. Make sure the keel is sanded and leave a little grit on the surface for the primer and paint to stick to!
Blog
Hawser holes cut
… ed for anchor hawse's. Anchor not yet fixed as will need to paint hull
Blog
H.M.S. BULLDOG / BEAGLE
Working through the many finishing touches to the hull, but it is essentially complete. Even got the first coats of paint on! The pre-paint preparation was quite quick as the hull moulding was well finished. Obtained the deck planking; this …
Blog
H.M.S. BULLDOG / BEAGLE
… mplete with a correct section and shape. Rudders primed and painted. The rudder shaft tubes had previously been installed into a wooden block glued in the hull to provide a rigid mounting.
Blog
H.M.S BULLDOG / BEAGLE
… cutter. Epoxied the outer frame into holes drilled into the hull and filled any gaps up with epoxy. Have left the glasses out until the painting is complete. The cut acrylic rod surfaces do require polishing to remove the cutting marks. Aft …
Blog
Sea Queen
… own for the undercoat then the finishing coat final coat of paint to the Cabin & hull
Blog
ytgn 13
… n particular the deck fittings. I am at present starting to paint the hull and it is surprising the number of spray cans required. My deck planking detail is not very good as the planks should be much thinner and not mahogany coloured, but …
Blog
HMS Diamond D35 - Build update Twelve
I'm nearly ready to give the hull it's first coat of sea going paint. I'm pleased with the lines and shape. I must admit I have spent a little more time on this particular build than I have other projects for some reason and this is not a D …
Blog
Build Update
Hello all, Ok, so getting closer to the Hull being finished, I've painted the Antifoul and Water line, I've gone for an Olive Green Antifoul, it mentioned this on the plans and found a Revell colour that suited. I've also sealed the Foredec …
Blog
Bits and pieces
… resent. The larger installed bits have been fitted into the hull: the fire monitor pump, the SLA battery, the drive train, and the towhooks with release servo. Various deck fittings are being constructed and painted. The stand for the fire …
Blog
Build Update
… onics just yet it may help others?? Last photo's are of the Hull with it's 1st coat of paint, I'm going for a darker Grey (Humbrol Sea Grey No-27) than the recommended light grey. I'll need to rub down with finishing paper and add a few mor …
Blog
plating
… as can be seen. Coming up the muddy river to Bridgwater the hull became stained. To replicate this I made a pond off polythene sheet, pored thinned oil paint on the water. Dipped the model down to load line, remove then dip again to the lig …
Blog
Fast Forward a Bit
… sorry I did not take too many pictures of the finishing and painting, in a nut shell I've sanded smooth and applied a coat of Primer and Varnished the interior of the hull. I plan to rub smooth with wire wool to get an even smoother finish. …
Blog
Vosper 1/16th scale crash tender
Hull now waterproofed with fibreglass cloth and Z-poxy finishing resin. Deck waterproofed using sanding sealer and lightweight tissue. With the various hatches and net rails in place, the wooden structure is complete except for the window f …
Blog
Vosper 1/16th scale crash tender
… nding sealer to prepare for adding the hatches etc prior to painting. 2. Add the hatches and raised sections on the rear cabin which would then be sanding sealed. 3. Cover the exterior of the hull with fibreglass cloth and Z-poxy resin prio …
Blog
Info for Vosper Crash Tenders and Air ea Resue
… on that, could be something else) I have used a variety of paints In the past. The best I came up with Involved using Dulux house hold paint and mixing It to match the colour but the nearest match In the modelling world would be Tamiya XF- …
Blog
Mersey Ferry Royal Iris(Fish and Chip Boat)
… ing the superstructure. to the deck which was fitted to the hull. Access was inside the saloons.Painting and interior fittings of the saloons had to be done at this stage as they would be inaccessible when completed. Photo 2 The stern with …
Blog
ytgn 8
… using epoxy glue and put the pins the whole way in. Then repainted the deck and strips with 2 part epoxy varnish. The heads of the pins are not flush in all cases so I will have to do a bit of careful fileling. Eventually I intend to cover …
Blog
Fairey Huntsman 31
… the propshaft and rudder. Fitted the prop sleeve and spray painted the hull and structure (see pic), I did it in maroon and white coz I couldn't paint it blue being a Man U fan, although my rugby team, Barrow Raiders, (and that's an oxymor …