Search
845 posts for “hull paint” · in Blogs
Page 20 of 31
Blog
Mounting the Winch servos
Having sealed the inside of the hull with two part epoxy, it was given a couple of coats of white Hammerite to ensure that there will be no water damage, and to make it easier to see inside the hull once the deck is fitted. There are two wi …
Blog
Phantom Tug
… update this time. The timberheads are all in, the bulwarks painted, deck laid and sealed, so it's on to the cap rails. There was no way to bend a flat piece of wood sideways to the curve of the hull, and knowing these would be painted, I o …
Blog
Sealing inside
… een filling and sanding set up two part finishing epoxy and painted on to the inside of the hull. A good coat went on and will need to set up. touch ups may be need for some areas . Rick
Blog
Steam tug Lyttelton
… , saves.....trauma? Anyway, we're up and running again. The hull is now painted and lacquered. The name lettering is laser cut vinyl lettering, courtesy of the Leeds Model Shop, whose mail order service is a life line at the moment. The rea …
Blog
Ink bled
… e after coaming is done and everything fibreglassed, I will paint the deck to match the hull, or a contrasting colour.
Blog
Water line
… st so decided to use it to put a line around the top of the hull to give a nice distinction between the blue and walnut woodwork. Just a point, the trim line was probably 20 + years old but still as good as new. I also applied the rear fend …
Blog
Morston - H A Kits (small version) Cabin fun
… thout a challenge. Just the Cabin roof to fit and its on to painting, I am thinking of a couple of shades of blue for the hull at the moment. I am planning to leave the roof off until I have finished painting the cockpit.
Blog
Princesse Loane Trawler Build (conclusion)
… ot posting earlier, but as it is "life got in the way". All paint is Testors Model Master, with the bottom of the hull painted with #4674 Leather up to the chine, then #4852 Green Zink Chromate up and over the gunwale. There is a strip of B …
Blog
Phantom Tug
Four The tug is evolving. The hull was 'glassed outside, and epoxied inside. Where the battery, motor, and electronics mounts reside the hull planking was 'glassed. The main platform was fitted and the rudder operation addressed. The counte …
Blog
Phantom Tug
Three Moving along on the catch up, the hull is 'glassed, sanded, and ready for some paint, plus have to figure out the rudder and how to activate it. The first coats of paint are rattle-can automotive primer from the parts store. My though …
Blog
70' WWII MGB
… is was epoxied in place and it fits snugly at the bottom of hull between bulkheads The rest of the hull was constructed as the article described until it came to finishing. I used the described method of pouring in fiber glass resin to wate …
Blog
Electronics installation continues....
… items to be fitted, was drilled, cut and sanded ect before painting in red oxide spray just to hide the white plastic. Once lacquered and dry, it was mounted to the aluminium cross brace struts which will be bonded into the hull in due cou …
Blog
39' Windboats Fairwind - roughing out interior
… ’ lengths ordered. That’s a heck of a lot of tiny paneling! Painted the engine room. The hull has no solid bulkheads below the waterline, so could also paint most of the inside of the hull, fore and aft. The transom, though straight in plan …
Blog
The whole boat
… or built, the main cabin and funnel from plasticard and the hull with its ply inserts for the cabin windows and the wavy rubbing strips straightened out. Getting the hull etc to this state seems to have cost as much as a small boat kit plas …
Blog
39' Windboats Fairwind - finishing the chine
… ly the same profile as the waterline, so it was easy to add hull below this, but at the bow the chine of course came above the waterline. I added balsa block in the area, cutting it first vertically, getting the chine shape from the ply tem …
Blog
Jet drives installed....
… ernal grills, I primed and sprayed the area black. Once the hull is ready to go in the paint shop proper, I shall mask the grills and the outputs on the transom and re-prime the hole hull. The nozzles, buckets and trim tab assemblies will r …
Blog
Preparing mounting holes.....
… again the areas were the jetdrive housings would sit in the hull and exit holes on the transom in preparation to mount the jet drive nozzle and bucket housings. To make a template for the hole in the hull, I painted on a layer of black tami …
Blog
Puffer update
… puffer it was to be powered by steam.That changed after the hull was built.When placing the boiler in position the chimney would have been in the center of the hull.Also the steam plant would have to be hidden not what I wanted.The Borkum b …
Blog
Scratch built, Working Steam powered Drifter trawler LT100, to 1:24th scale.
… his before so after some thought I tried mixing artists oil paint with Titebond 3 glue, this took far too long to dry. I then tried artists acrylic Gouache a thick acrylic and Tamiya acrylic mixed with Titebond 3 (separately that is), this …
Blog
HAKITS MORSTON
Things seem very slow at the moment what with painting the hull, the new paint has arrived now and so have been able to put the final coats on the the bottom and the sides. I have concluded that there is only so many times that you can pain …
Blog
HARTLEY FLARELINE, SOMETHING COMPLETELY DIFFERENT
… y angle, all screwed together with 3mm screws and nuts. The hull supports are from 8x8mm square brass tube, soldered to brass plates and bolted to the frame. The wooden support rails are drilled for a tight fit over the sq tube, set at the …
Blog
Eastwind
… boat was a bit of of a challenge, but research helped. The hull is that of a 36ft Coast Guard life boat, but it differed from the waterline up. I found an old plastic kit in 1/48th scale of the life boat and between a Dremel tool and styre …
Blog
Deck Hatches
… provide plenty of access to the radio gear installed in the hull. The plan calls for coamings (3 x 6 mm) to be glued around the edge of each of the hatch openings. Strips of mahogany were cut to size and mitered on the ends. The mitered cor …
Blog
Cabin assembled
… ..time..to..assemble the cabin. The cabin is located on the hull. The aft 1/4 inch of the cabin lays over the hatch, from what I understand the hatch is slid forward under the cabins aft edge and pressed into place. Anyway, once I had my ca …
Blog
Euro-Girl Semi Kit Review
… a thorough examination of the Semi Kit Parts 1,2 and 3. The Hull is a chopped strand GRP Hull and is extremely well made. It is thick enough not to twist and is approximately 2mm -4mm thick. The thick parts are where it is going to take the …
Blog
HAKITS Morston
… ed to the workshop alas! Have been moving on a bit with the hull painting, a somewhat slow moving operation it seems. I have now painted the lower hull and upper hull, except for the final coat which will be applied after the deck and super …
Blog
HAKITS Morston
… ch changes visually except undercoats are coming and going, painted on and sanded off. All of the model has now been undercoated and am now working on the bottom of the hull and the sides. These will be taken to first top coat in the next f …
Blog
HAKITS MORSTON
… the big cover-up and set about priming the top part of the hull and then rubbing down first coat. I did not know exactly how to go about the order of painting the model but decided I would get the tricky part out of the way first. It is no …