This is a re-issue of my previous post as the link to the video failed.
It shows a Sunday morning's sailing at WMBC through the 'eyes' of my 46inch Perkasa.
Details of the Club can be found here:
https://www.worcestermodelboatclub.co.uk/

Video of Sunday at Barry Boat Club. Camera mounted on my Perkasa

Decided to sail the Solent so took some video to share. Uses 2 Bhuler 12v brushed motors with 4 bladed 45mm PropShop props and 12v 12AHr SLA. Twin Electronize ESCs. Radio is Futaba 6Ex but I will probably change to the Taranis so I can get better control using some bespoke Tx settings to co-ordinate the props and rudder.
Lifeboat crewe had been on a night out so not quite vertical. Aplogies for the shaky video, it's difficult to sail and video at the same time.

Looking for a new project i decided to try to make an outboard steam launch. The engine and drive took a while to work out but in the end it all came together well. The boat travels at a nice speed fueled by tablets for lightness as the boiler and engine are quite heavy for the boat size which is about 22"long. There is a brief glimpse of my paddle steamer that i also made. Pictures taken at TILFORD rural life museum Farnham. Next show is Easter Saturday Les Breame

Coal fired Clyde Puffer project. GRP hull with vertical boiler and oscillating engine both of which i made from scratch. Goes very nicely . pictures taken at ilfracombe boating pond. Les Breame

GVMBC Night Sail 29/03/17
A good evening's sailing. Boats looked better the darker it got.

I acquired this boat part built some months ago through Dave M.
I have not put too much scale in detail but I am quite pleased with the overall finish. it is powered by two brushless 1250KV out runners and in the first sea trials I used 12v lead acid batteries. (That video was posted a few weeks ago - mdlbt.com/26793).
This video shows its second sea trial after I was persuaded to use lipos. The difference in performance is very pleasing.
Thank you Dave M for your help and advice during the build.

These 3 boats are scratchbuilt by 3 separate builders. Renown was only recently launched. All are 1/72 scale.

This is my 6 month in build of a fully working fishing boat .she has a real I have modified and put a 20kg winch servo so u can real in and out and have drill a hole in to the real and put another servo so u can lock the reel out to.made a back plate on the end of a cut off rod and bolted in to the hull. She has full fpv from the wheel house with a 360 spin HD camera and have even put a digital amp meter so u can look at to and see how mUchida power u have left full running lights controls off hand setc to twin brushless motor water cooled and a large 100 amp esc with air fan and own power supply going to take her out tomorrow for her maiden voyage. Witch has bin a real long time coming and a lot of blood sweat and stress to get it all to work but finally I'm there hope u all enjoy and like what I have dun thanks for reading my post Ben

I bought a used hull of the Ayton Cross and look all over the internet for some plans but found none.
I did find a lot of images though.

I bought most if not all of the fittings and since have decided that the way to go is to make what you can from what I can get hold of.

So all other model boats are and will be scratch made.
I have two on the burner at the moment.

Anyway some of the Ayton Cross looks right some of it does not.

But I can always do it again as I hopefully get a little better.
This one again is awaiting Ballast and it will be ready to go.
I fitted two Engel 12 volt motors and made the mounts in grp then Laminated them into position..

Everything has been hand painted and slightly aged .

The bow thruster was made using some household plumbing pipe a small propshaft Again home made and it works very well.

Something to play with as I build hopefully better.

Well this was the very first model boat i made.
A springer tug.
I made a mould and then made a few just in case i was to the point of everything going wrong at least I could start another one.

Apart from the home made GRP hull everything else was made in Balsa wood.

Since been scrapped but the hull and all the electrics ect have been reused again for another version..

This is my super airboat mk1 built in the 80s was in a real bad way when I got it only payed 30£ for it and have put a lot of time in to it to get it to where she is now have updated the rc control and receiver to a 2.5g flysky 6ch apart from that she is original and still have not seen or found a mk1 the only other one I have seen is a mk2 hopefully u will all enjoy and like what I have dun to her