Scratch built in 2004 from my own plan. Two layers of planks on ply frames, ply deck planked with 3/8 1/16 strips. Length of hull 50" by 13" breath. No motor sail only, winch for main & mizzen, sail arm for fore sails. Featuers a centre plate lowered by gravity and raized be a drum winch, also an expanding rudder, this has two servos to opperate. sails can be reefed or removed depending on weather conditions. Very good sailer Just goes in my car with the top mast & gaff boom lowered.

SCRATCH BUILT TRAWLER
USING F/G HULL ALL WINCHES AND DECK ITEMS ALL SCRATCH BUILT

Built from scratch from plans supplied by my hobby store. has a fully remote controlled operating "elevating wheelhouse" with scissor type lifting legs. operating nav lights, fog horn and twin radar units. Also has remote operated forward winches for attaching pusher barges to the bow pusher posts. fitted with twin kort nozzles, handles a treat, steers well and could certanly push more than 3 barges!

HI fellow modellers, Another model from the RADMC fleet at the fleetshaven workshop and boat yard in Ponthir.This model was scratch built using a fibre glass hull and plan obtained from a fellow modeller at the Bridgend Show in 2007. The front door and some fittings are made from plastic card and tube, decks are from ply and timber. On board figures are from the pound shop and car boot sales, modified by myself. The on board tank and half truck are RTR models that I have modified their looks to fit into a WWII theme for the craft. This craft has twin drive, 400 motors via 2.5/1 gearboxes. I tend to use both sticks on the TX for drive as this allows me to turn the model on a six pence.The dispatch door works from a rotary pot on the TX and via a rotary sail winch servo in the hull. I have just modified my Planet 5 TX to allow me to change my radio gear in this craft. This model has had meny trips on Cwmbran Boating Lake and at shows the society attend during the year. Still haven't allowed the tank or half track to run off the landing craft up the lake side slipway. one day I might get it on video. Hope you enjoyed the photo's. Regards GreyWolf

HI bit more deck works done winches crew , that's it for now,
Back on the shelf , to wait for running bits . time to back to trawler build......Larry..

Built from Aerokits kit originally but rebuilt/modified many times since then!
Twin 540's (geared) 6V Pb Gel battery for drive. 3 Blade 50mm props (contra rotating) lights (cabin, running Ights and searchlight) on 4.5V Deacs. radar scanner and winch on same supply, radar display screen on a single AA 1.5V.

Fleet Systems radio and speed controllers, Futaba rudders servo, RCME servo driving cam/micro switch unit for lights etc.

Hi" I thought I would put my new rebuild on for all to see ! I found this old Marblehead yacht as a wreck. She was gathering dust in an old reclaim ferniture wherehouse whilst we were on holiday last summer. Been told the yacht had been originaly scratch built in 1950s from a plan. She took me about half a year to rebuild. New parts as follow hiteck sail arm winch with 18lbs of torque. New futaba servo for the rudder. New sails & booms rigs & fittings. New deck made from plank strip wood & varnished. Also finished in painted Ivery white. She sail well in lite to strong winds At my local boating lake at Sheringham Norfolk .
works well on a Spekrum DX5E But can work on any other 2 channal transmitter .
Hope you enjoy the photos .

As the name suggests, this is a scratch build sort of tug. The hull is based on a (very small) Pinacce photo of a model steam open boat. I did not fancy making a steam unit (time is the problem) and I had had an idea of doing a tug for quite a while. I liked the shape so started in the usual way. I wanted to keep the cost down and so almost everything is scratch made, though a few bits were "borrowed" from where I work - an engineering firm. Most of the work on this model is more of an experiment for my next tug which will also be from scratch but will have everything working. The "Archer". The winches are at the moment none working, the doors do not open, I have no idea if there is any tug that looks anything like this but I am very pleased with the result. I hope you like it.

46 inch Crash Tender rescued from E-bay. Currently in the process of total restoration and have had to scratch build the entire super structure. Have fitted a Merco 61 engine with tuned pipe (the noise is awesome).

Have gone for it with the radio control- - employing a Robbe F14 plus an extra 8 channel module with decoder. So far extra controls are : each monitor (scratch built using brass pipe & sheet) left & right (using Robbe pulley set to give me 270 degrees travel), two Irvine water pumps, (real car) hooter, winch (using gearbox from Maplins) and movement for jib and search light.

My Amsterdam is done from an old Latina kit. it has the board on frame hull construction of the older kits. I've done some modifications from the kit such as, larger bridle winch, bridle assemblies, extra aft deck detail, lowered engine room cover, brass lifting boom, recessed anchor pockets, enlarged rudder and various miscelaneous detail changes.
John

This is BG Coulies built by Geoff Lewis. its a French Harbour tug that he built following an article in a well know magazine, advertising a set of plans, thanks to the office photocopier he saved himself several quid.

Coullies is driven by 2 550 motors driving Graupner scothell drives (not yet independantly controlled). 12v 4ah Gell battery and some roofing lead makes up the balast.

The frames are 3mm MDF with a balsa and ply skin built to 1/32 scale, the figure sat on the anchor winch used to be a German infrantry man. He recently obtained some Beccs transfers to add some more finishing touches including the french flag.

What does Coullies mean? (pronounced cooee) find a dictionary...

"BOO BOO Kitty" is a scale model of a Crosby designed Cape Cod Cat Boat.[USA] it was built from scratch at a scale of 9.04" = 1"; the model being 26.5" oal.

The dimensions were taken from a book that highly detailed the building of a real Cat Boat.

The hull is plank-on-frame with epoxy and glass cloth as the final surface. A separate and detachable fin keel was used for sailing of the centerboard model.

Radio controls were a Hitec sail winch [HS-785HB] and one servo for the rudder with a 2 channel JR transmitter.

Copying the book plans, scaling them down, and construction took up the winter of 2006/2007. The model is sailing better than anticipated on a local lake in Langhorne, Pennsylvania.