After a re-paint and total refurbish she was tried out on the Omskirk and West Lancs Model Boat Club lake at Hurlston Golf and Country Club Scarisbrick Ormskirk Lancs.
She is not mega fast but sails well as you can see from the video.

My latest project - Hull and some bits from a static display model, based on several photo's of Greek fishing boats, Mtroniks 400 motor, & 15A ESC, 12v SLA battery & 30mm 3 blade prop. Fish boxes from Coffee shop stirrers, Fish from long grain rice, Crew from Pound shop (Soldiers chopped & reshaped. )
She sails fairly well on first trial this week at Weymouth & Portland MBC, Miles Cross Farm lake . Hope to post video soon.
Chris

Greetings from Hollywood, California. 😎 Many thanks to David Metcalf at Metcalf Moldings for his advice and for so graciously replacing parts I messed up. This craft has been swimming pool tested (after all we're in Hollywood) and it ran beautifully. Next stop is the local pond. I chose brass counter-rotating props. Those are lithium batteries tucked under the sides. I chose to recut the decks out of wood. Brits rave about plastic but I found it difficult to cut and forget about sanding down the edges. (I guess if you cut it properly you don't need to sand the edge.) Major mistake: watching a You Tube video that told me I should make brass joints using a Propane torch. it will make a good joint but it MELTS ALL THE OTHERS. There was a lot of learning here for me and thanks to David's fine kit I think I'm somewhat of a better model builder.

This model of the tourist attraction in Liverpool a few years ago.Sadly after a couple of mishaps all four have been withdrawn from service. The model however survives. it was scratch built from photos and site visits by myself (Max Ferrie).There were no plans available. it is about 28inches long and roughly 1/12 scale.It was built almost entirely from plywood. As you will see from video it operates on land and water. it is six wheel drive using differentials on all wheels. When in water it is prop drive. it has two small electric motors for power, the wheel drive being very low gearing (too low really it goes very slow on ground). it was completed in 2010, and is filmed sailing at the portable pond at Toys For Boys in Waterloo in 2010. it has sailed at Hoylake MBC also.
It is powered by two 6volt 4AH batteries in series to give 12volts.

Following the legendary Keil Kraft Eezebilt plans for a Mermaid Ocean going boat. Plans exploded to 200%. Trying to build it completely out of Plywood and Foam Board.

OA Length 710 mm, Beam 180 mm. AUW 1.98Kgs.

She carries the name 'JAYSHIL". it is a portmanteau derived from the names of my late parents.

Model features working lights as prescribed by the international Maritime Authorities:

http://www.bosunsmate.org/seamanship/lights.php

In keeping with Rules 22 and 23:

http://www.bosunsmate.org/seamanship/rulesoftheroad.php#rule23

Brushed 550 motor, Reversible ESC, 2S LiPo, Turnigy Blue Prop, Working Lights and indigenous Sound Generator unit.

Video is available here: (you may need to turn down the volume a bit as the horn is rather loud)

I would welcome any queries and/or comments on this build.

Thanks and Regards,

VC

My own design deep "V" hull with upper-works loosely to 1:15 scale replica of the Mitchell 31 boats previously used by various Hampshire constabularies in and around the Solent. The intention is to fit this model with a working, rotating, radar scanner using the servo motor and gearbox from an old video camera lens system; working lights including flashing blue police lights and a sound-alike "wee-wah" siren - just for the hell of it (and because I can)! Technical details: Hull length: 867mm. Construction: GRP layup with 1.5 and 3mm ply and balsa deck, cabin etc. Motor: MFA Torpedo 850. Propeller: X50mm plastic. Battery: 2 x three cell LiPo pack in parallel. Speed controller: Mtroniks Viper 25Amp. Radio: Hobby King 2.4GHz.

Just a short video of Ian Pott's recently completed Model Slipway Tamar lifeboat. Looks and sounds good with action sound unit

This is a fun boat!
With a steam engine that really runs, it is quite a crowd pleaser.
The tank and parts are brass, and silver soldered together. The heat source is sterno, placed in the tray and Ignited. This boils distilled water in the boiler, which is vented to the piston. The hole in the freeboard is the "exaust".
I'll have to post a video of it operating.

Originally designed and prepared as a fun entry to the MMI Solar Boat Challenge.

Scratch designed and built of depron to run in standard house guttering - size and construction details on the video. There are a number of 'solar' boats on another video of several including the eventual winner of the challenge. inexpensive, fun and unsinkable!

Super little kit making a great model. Essentially styrene with added mixed fittings then super detailed and weathered.

Video rather shaky as operating camera with one hand and RC with the other - will Improve and add soon.

This is the video that should have appeared first!! Please Ignore the Buoy incident , I was not concentrating watching my wife with my phone! if you notice the turns are very large, so I have increased throws on the rudders, will try again and if not, apply some mix to motors through the rudder input on the Tx. Enjoy, Brian

Well here is the video, hope it works. Please Ignore the buoy incident! and also my wife's finger half across the lens!!! Brian