Just 2:48 minutes​ of video clips to illustrate the fun of Sailing RC Lasers ! .

Finally got a good day to try the new brushless motor. Boat goes 100% better now (if a bit noisier) 3s 25c 2200mAh liPo got a bit too hot, so probably need to up the C rate to 40 to keep it cooler (maybe install a fan as it's closed under the seat) It's pushing a 6lb boat with a 26mm jet with a 3000kV brushless so it has an excuse to get hot, (only got down to 3.7V/cell after that run, so not too bad). Runs with a more scale look now which is what I wanted. Took a bit of experimenting, but got there in the end. Thermostatic cooling fans for the motor worked well, and within 10 mins the motor was cool. Only used around 2/3 throttle so as not to stress the coupling too much (you can hear it protest a few times, - silicone tube slips slightly making it squeal)- automatic rev limiter😁

Sorry, vid is blurry again ☹️ (original's fine -HD) but something happens when it goes through my movie editor then to YT. Keep procrastinating about getting a better camera (or maybe it's just the editor. - More experimenting, this is getting tedious😐

Set the new Surpass 3000KV 36 diam finned in-runner up in the boat, and did a tank test. Lots more power than the HV brushed 1200kv 550, but with higher idle. Re-did the reinforced silicone coupling and fitted a small collar to the inner end of the motor shaft to hold the tube from moving forward against the motor, as with the extra torque of the in-runner, it was trying to twist the tube off the shafts. Seems to be hanging in there static which is a promising sign. Once running, the load will come off which should help.

Runs full at around 4A and the battery holds at around 3.8v/ cell )alarm is set at 3.6 for safety, (as a sort of rev limiter) performance should improve a bit now. Have to wait till tomorrow as the restrictions end at 6am Sunday, (then have to hope for good weather for the test) The prop in the jet is a 28mm 3 blade racing prop which I modified to fit. Don't think I'm going to get much more out of the jet unit without it exploding😁, (it's only plastic I think, not GRP), - might have to buy a back-up and fit it with better quality bearings etc. If the jet was in the usual 'plastic' 24" toys it would be a rocket, but it's pushing 6lbs which is a challenge😀

Note the police chase outside in the background😁- always action around here, lots of hoons in cars😁

I trial fitted a thermal switch to the fans in the dummy motor, which is mounted on the 540 motor. It starts the dual fans at 30deg C and switches off at around 20deg C. Bit hard to hear in the vid (plus the YT transfer removed the middle of the vid, -there was a gap before I put the soldering iron on again,- and at the end don't know why it does this, - doesn't like the format I think😠) Anyhoo, not doing it 3 times! (clipped the end 10 secs off the previous try as well😠)

Fan switch is powered at 8v via a small voltage reg from the main battery (3s 2200 20c) and works pretty well. All fully hortomatic like😊

I decided to risk a salt water trial, as there is no place I can think of with fresh water and a smooth beach or ramp which doesn't involve a 100 mile round trip (most beaches where I am are ocean beaches and others are soft sand/shell. The only lake I can think of is 112km away and I'm not THAT keen. Launching went ok but retrieval was another matter, not helped by an 8mph side wind (looks calm but is windy) Had a number of goes and discovered a few things which need changing, (extra front guide posts and rollers either end of the pads) The rubber resting pads stick like glue so I'll have to make some pop up rollers at the ends.

The pads hold the boat slightly above the centre rollers to avoid damage and stop it sliding off while shifting it. New front guide posts are needed as the boat only draws about 30mm and goes right over the trailer with it underwater 😮(no prop or rudder sticking out,) so it might help locate it when coming in. Jeep had truckloads of power (just fitted a new even lower geared -geared motor -1000rpm/min @ 12v), but unfortunately being only 2x2 (not 4x4) and being half the weight of the boat/trailer combo it couldn't get a grip in the mud, so needed a bit of assistance, (as did the boat getting onto the trailer). Cut out most of the vid with the boat missing the trailer about 10 times, but scored a direct hit once😊. Heaps of fun trying and heaps of washing and CRC when I got home! Going to need some new bearings at some stage, - the ones in it are rubbish and have only lasted for about a few hours running, noisy as anything now, even with gallons of oil. Stainless NMB ones next if I don't change the jet to something else, (another thought on propulsion happening)💡

Tested the new reversing bucket, and it has improved reverse power quite a bit (actually was backing into a strong wind). Bit hard to gauge the reverse steering as there was a 10-15mph wind blowing the boat all over the place, (looks calm but wind funnels through the area from either end at times). Performance hasn't changed with the new grille unfortunately, but the flow looks slightly better. I noticed the reduced brass nozzle I had made was creating a small amount of back pressure, so have re-fitted the original oversized plastic nozzle for the next test.

More work on the little boat today #lockdownfun

Finally got a good day, so raced down to the pond and threw the boat in. 2 problems, 1: battery had run down a bit with all the testing, and the new 18kg digital servo winch needed every bit of 4.8v, so functioned intermittently, meaning not much sail control, 2: jib boom needs a kicking strap to stop it 'skying' and tangling (knew it would happen but wasn't a worry). Apart from that, everything worked perfectly ( cheapo China Futaba knock -off rudder servo still worked fine on the low battery which is a bonus)

Sailed brilliantly like it did over 40 yrs ago, and as it's set will sail hands off on a reach, being nicely balanced, (even with the crappy jib,- which I had to make,- well actually my mother made for me,- back in 1980 after the original was stolen by a kid at the beach, while my back was turned😠) Funnily enough it was made on the same Bernina I used to sew (horrendously) the jib foot after trimming it for the boom a few days ago.

A few more things to improve and add, but pleased to have it back on the water. Another crap video, -seems to get blurry once it's been through the movie editor and You tube ) One day santa might bring me a Gopro, ("yeah right"!)

Second test was slightly better, using the aluminium spiral cut universal which came with the jet unit. As you can probably hear, it was horribly out of balance (even with cable ties to reduce it). It was not even drilled centrally and the spiral is right hand when it should be left hand, (like a spring twisted against the wind, it wants to deform). Slight improvement in speed on the first test (no slip this time) but the noise was horrendous.

Have pulled the jet apart and found that the 3 blade prop is around 1 mm too small for the hole, causing cavitation (see loads of bubbles in the jet stream) which is causing loss of thrust. The prop is the wrong type as well, with rounded blades, so I have modified a larger prop with more pitch to fit snugly in the unit to hopefully increase thrust. The shaft is also wrong, with a flat cut almost half the diam and carrying on through the bearing, allowing the grease to fly out.

I actually saw a Chinese site on Al Expr stating that "some dimensions on the product may be different due to the number of machines and operators involved in its' manufacture," SERIOUSLY!!??? their quality control must be utter crap and the operators not skilled enough to eat their lunch😐 Why bother having a dimension at all?? Little wonder nothing fits properly.

Unfortunately, most model shops sell the very same stuff, unless you want to shell out muchos dolleros for European stuff. I have just ordered some 4mm silver steel to make a new shaft, so a coupling or silicone tube will fit better. Also ordered some solid connectors to try. Vibration is wasted energy so it needs to be eliminated. Hopefully the mods will improve things and allow the motor to run on 4s rater than 3s. Worked out that the motor is only 1200KV, so it's only doing around 13,000 rpm under load. Probably will need around
18,000 rpm for proper performance. Onwards and upwards (or forwards as the case may be.😁)

Sorry about the blurry vid again, but my camera lens is knackered.

Smoke air and water switching sequence, (sound's out of sync for some reason,)

A bit more refinement on the timing but getting there. Finally got the voltage regs from China to complete the system. A bit noisy, as the water pump is dry,- quietens down with water. Switches in stages using Grahams magic timer, - 1. smoke on, 2. water and air on. There is actually smoke running constantly at a reduced level once everything is running, but very hard to film. I could turn it up but I don't want it to look like it's on fire😂

"Fairey Huntsman" - Following renewed recent interest from Model Boats Website members,
here are three variations from BMBC members of the popular "Huntsman".

(Ref from Wikipedia)
Fairey Huntsman / Fairey Huntsman 28 / Fairey Huntsman 31: The design of the Huntsman and its smaller sister, the Huntress were the inspiration of Ray Hunt and designed by Alan Burnard.