This is a first try at a simpler quieter smoke unit. I used the smoker box/element off the Heng Long tank/car smoker unit with a 40x40 5v fan (the fan being voltage controlled by a 5v UBEC and the lot being run by a 2s Lipo (with a y splitter for the fan UBEC and the element using JST leads. Doesn't smoke that well as I had broken then repaired the element previously, but the other one I have smokes a lot better, and has a better type of element (possibly a newer version) Some photos etc on the smoker discussion. Unit is almost silent (the noise you hear is the camera and outside noise, as the window was open)

Building a German Police launch right now and thought that the radar scanner components were a bit 'heath robinsonish', so decided to see if I could make an alternative unit.

Photo 1 shows the Radar scanner parts obtained from MMB (ebay) for the princely sum of ONE POUND !!!!! plus 28p postage, and construction is of a medium soft resin that isn't prone to breaking or splitting when shaped or drilled, and a short length of 2mm brass rod becomes the drive shaft. This particular unit has a 44mm sweep bar but there are many other sizes available

Photo 2 shows the drive motor which operates on voltages between 1.5 and 6v, ideal for the control driver which is the next item. Available from saih.tan on Ebay for under 7 pounds, and if the motor is mounted on a removable bracket as I have done, this unit can be used in several models without the need for major 'surgery', the motor and radar shaft being connected with a short piece of rubber tubing

Photo 3 shows the receiver driven radar motor speed control which operates from an auxiliary receiver channel and takes the motor voltage from the main receiver supply, thus obviating the need for a separate supply and switch.
This unit is available from www.mr-rcworld.co.uk and costs a staggering 14.50 post free sheesh !

I must add here that I am in NO way connected to any of the suppliers mentioned here, but just though some other modellers may be interested in 'home brew' accessories and suchlike.

An ebay buy now fully restored custom made and commercial fittings. Power unit Electric manufactyrer and voltage unknown it will soon be time to test it on the water

J. R. MORE - LAST OF THE LARGEST STEAM TUGS BUILT ON THE CLYDE. The best looking tugs ever built!

This model is scratch build at 1:48 scale of the SAR&H Durban tug J. R. More, which was the last large steam tug built on the Clyde in 1962.
It took over 2 years to complete this model, which was my first scratch build from the modified plans of a sister tug called the F.C Sturrock, which was also stationed at Durban as the shift tug for that harbour. Other tugs of the class were also stationed at Port Elizabeth and Cape Town.

The J. R. More was the newer day tug in Durban, most often used to service the Union Castle ships and others in, out of Durban and remembered by so many visitors to South Africa of that time.

This model tug on the water has differential motor control, software linked with the rudder, can go about on the spot and a delight to sail as a model, capable of 6 or more hours on the water. Working Rotating Radar, lights and woop-woop sounder as per the original tug. I would also like to install the Telegraph bells, however these would drive fellow modellers to distraction, as they were a very distinctive sound and very regular, Implanted and well remembered by the crews and those in and around the harbour, even today. The engines on the other hand were almost quiet and by all accounts very reliable.

This model is ballasted mainly by two 7 Ah 12 Volt SLA Batteries for the main drive motors and a 2 Ah 12 Volt SLA (Aft ballast) for the Lights, Radar and Sound unit. All up weight is 14Kgs and capable of above scale speed from the two MFA 6:1 ratio Geared Motors driving two 4 bladed 70mm screws.

This model has onboard charge regulator circuit, built-in minature dual volt meter to allow quick on-board voltage inspection and single plug-in charge and regulator socket for charging all 3 Batteries together.

The actual full size J. R. More tug still survives and can be visited at the Durban Maritime Museum in Durban, South Africa. Local supporters are undergoing essential repairs, restoration and preservation with private and company financial support.

J R More is the only surviving large steam tug left of this class and as Important to the skills of the Scottish shipbuilders of the Clyde.

Purchased secondhand, upgraded to a proper motor esc rather than the original/factory on/off micro switch for the motor power. Running a graupner 600 race motor and 7.4 lipo, basically just to run the brushes in on the motor before raising the battery voltage,
bit of a shaky video but try holding the transmitter and filming at same time on your own [ha ha].
it does have the capacity to move a ot faster, but would sooner work the motor in fully first

HI Fellow Modellers,
Another model from the RADMC fleet at the fleetshaven workshop and boat yard in Ponthir.This model was built from a Caldercraft Kit, This model came into my possession for the price of 20p, a raffle prize at Bryn Bach Model Clubs OPen Day 2010, when it was built is unknown. The item being made for display use and not finished off, no internal electronic fixtures. Did have a prop shaft and prop that had not been fitted correctly. 50% of all the fixtures had to be removed and refitted before they fell off, some didn't stay in place from the show back home. The model was finised off using a photo of the Milford star on the internet. The fish boxes and figures being obtained off DON one of the Society members who had a mould to make them in white metal, only required cleaning up and finishing off. A graupner 6 volt steam unit is fitted in the funnel and to make the boat a little more realistic on the water,a maplin steam sound system has been used to generate the sound of the engine. A simple mod allows the revs to be linked to the engine voltage. The drive motor is a 550 with the lowest revs I had in MJB's this was married up to a 2.5/1 gearbox I also had in stock. The main motor and steam unit are supplied from a 7.2 volt nicad racing pack. This model has had meny fishing trips on Cwmbran Boating Lake and at shows the Society visit. Hope you enjoy the pictures, Regards GreyWolf.

HI fellow Modellers,
Another model from the RADMC fleet at the fleetshaven workshop and boat yard in Ponthir.This model was built using a Billings Kit, bought for me as a Christmas pressent in 2009. A graupner 6 volt steam unit is fitted in the funnel and to make the boat a little more realistic a maplin steam sound system has been used to generate the sound of the engine. A simple mod allows the revs to be linked to the engine voltage. The steam engine rotates using a stripped down minI servo, fitted under the motor housing on the deck, again linked to the main motor voltage. The two 9.6 volt AA batteries and control gear are mounted under the boats floor, forward locker, a minI servo for steerage is fitted under the rear seat and the receiver is located under the wood pile. Figures are self made from items obtained from the local pound shop. The modal can be seen sailing at Cwmbran Boating Lake or at shows the society visit. Hope you enjoy the pictures, Regards GreyWolf.

Lesro Sportsman kit, wood sports fishing boat 33'' in length, weight about 8lb. MFA 850 on 12v (10 NiMHcells 3.5ah) MTroniks 40amp esc, X50 prop. Built by Ian Gardner.
March 2010. I am now using 12 cells and a Graupner speed controller. I added watercooling too and the boat goes noticeably faster- but melted a fuse holder on first outing so I need to upgrade some of the wiring. There was also a bit of prop aerating on turns so might reduce the prop size.
The last photo is with increased voltage.