Stolen Boat. Please be on the lookout for this beautiful KRICK VICTORIA complete with a Chedder Puffin Steam Unit, This boat was stolen from a member of the Mutual Model Boat Society, Heywood, Manchester. when some scumbag broke into his workshop over the weekend of 5th 6th September 2015. as well as his pride and joy they also stole a Spektrum DX6I / 3 x 40Mg / 2x27 Mg Tx's, plus tools???.

Should you hear or be offered this boat please contact me. or the police
Colin Travis 07905028298

Police (Scotland) 1.12 scale. made from a Semi-Kit by Models by Design, built 2014.
This is modelled from the interceptor42 range by Safehaven Marine. This is my first full build of a model, having only done restorations previously.
Model length is some 42 inch, beam of 12 inch. (106cm x 31cm)
Power is by twin E-Max BL2826 Brushless motors and 1, 80amp speed controller running on 2 NiMH 7.2 volts.
Fitted with Action electronics Police siren, and with detailed rotating blue lights and searchlights.
I sail this at Cold Knap Lake Barry Vale of Glamorgan, and I am the Founding member of the Vale Of Glamorgan Model Boat Club.
Also included is my Portland Pilot interceptor 42 which was the original prototype from Models by Design which I purchased and added lighting etc, this runs on Brushless motor running on 12Volt lead acid.
Visit our website at http://vgmbc.org/

Eezebilt 50plus series (see http://eezebilt.tk/PTBoat.html for free plans )

20" long - designed to be built in a bedroom.

Cheap (£6 raw materials) starter boat for introducing youngsters to modelling...

This 1/12 scale model is based on the Aerokits Solent Class lifeboat. Over the past 5 months it has been under going a major refit. I originally built the boat about 35 years ago and got the "bug" again last September. I've done the best I can to make a silk purse out of a sows ear.

Its powered by two MFA Torpedo 800 electric motors. power comes from two lead acid batteries, each rated at 12v 7Ah. Control is provided by two Mtroniks Tio ESC. The twin spade rudders are linked to one servo. Each ESC has its own receiver. I found that one receiver, using a Y lead, could not continuesly keep the two ESC supplied with a signal and they kept going into Failsafe mode alternately. I got round it by binding two receivers to the one transmitter. Within the engine compartment is an automatic bilge pump. Two probes detect if/when the water level rises to a certain amount in the bilge and activates the pump.

The model has working radar scanner , navigation lights, search light and blue flashing light.

If you want to see the boat in action please go to my You Tube page at https://www.youtube.com/user/coljacktonvale

33" Dumas kit of the PT109. Not very stable boat with little freeboard it doesn't inspire confidence at speed. 😭

Designer: Vic Smeed

A 1:12 scale model of a Thorneycroft RAF launch, length 43in., beam 12.5in Suitable for 2.5cc upwards. Excellent for R/C. Completely detailed on two large sheets.
Myhobbystore uk. MM412

I built this Range Safty Launch two years ago and I am now changing the hull paintwork to also include a water line. I never got around to doing this for some reason.

Range Saftey Launch

I purchased the plans for this model after my late father passed away, he too was building this model but failed to finish it before he died. My father was an Ex RAF Patrol boat pilot, hence the design was appropriate. The plans (Two sheets) are really well presented and easy to use. Each of the sheets provide ample detail to construct the basic model and if you are an experienced builder then these should suffice. However, a little research may be required to put the final touches together for the completed model (If you are a perfectionist like me). These plans are suitable for a novice as a first time project. This being my first attempt at a scale model. The boat once completed sails really well. I fitted mine out with electric motors, speed controller etc and when on the water a few heads turned! Fantastic plans GO FOR IT! Roy McCluskey

Saw the plans of 'Farmont' and could not resist the challange of this model. First problem was where and how to creat a removable cabin and decided on having the whole top removable other than the forward and aft decks. I also realised that the plans were simplified so a bit of research on Google revealed pictures of the real things for sale and some indepth pics of the boats being constructed. They omitted the bow breaker for ease of modelling but short cuts are not in my vocabulary. it is also difficult to visulise where all the stair cases go, so going online helped clarify this. I opted for a plank on frame construction covering the hull with a single layer of fibreglass and using lite ply and plasticard for the cabins. The deck planking was marked out with pencil before varnishing. I also wanted the boat to be fully lit and both radars to be operational and counter rotating (looks better from a spectators point of view). Completion date sometime in 2015, watch this space!

Just started work on the Torpedoes for My Aerokits PT Boat, the ones in the kit don't look quite right,

This is my scratch built inshore fishing boat, I adapted the plans from a model boat mag. The hull and deck are planked using cut up blinds from Ikea (they are made if Lime) it has working lights and radar via a 4 way switching unit on one channel, the working winch and trawl net are worked from another channel. Powered with an 18v drill motor working from 12v lead acid battery

This is a 40" long model of a gas powered Berkley Company kit of a US Air Force crash boat from 1955. The plank on frame kit was in production for about 10 years and was meant to be powered by a model airplane gas motor with a single shaft. it depicts an experimental 50 knot rescue boat (painted in a peace time color scheme) during service with the USAF. if successfull it would have been put into production designed to be a replacement rescue craft for all Air Force 65' crash boats. Unfortunately for the crash boat program the Air Force lost interest as helicopters were become a reliable way of rescueing downed pilots along the coast. The prototype and a sister boat were scrapped, as was the entire program.
The model was given to me to be restored(top picture) for the son of a retired USAF veteran that was a crash boat crewman. The model was built in 1957 and had been run a few times on a tether line, R/C was pretty expensive back in the day. I stripped the hull, filled in all the cracks and rebuilt the mast. I added a small boat, davit, liferaft, coxswain station, spray shield and deck hardware among other things. Actually all the owner wanted was a paint job, he was very happy with it's new appearencep! Although I fiberglassed the wooden hull and made it watertight, the owner doesn't plan to run it, just a memorial to his dad's service. I really enjoyed working on this "rare bird".

The 48 inch Sterling Corvette. The company went under long ago. Finding the kit complete in the box is so very difficult. One of the most gorgeous private boat kits ever. I attempted to build it twice in my life. The first time Vietnam got in the way. Later a move from New York to Los Angeles got in the way. I found this completed boat and bought it from the owner. I hope to find the kit some day and build my own FINALLY and do as good a job as this builder.

HI to all you Fire Boaters,
I have decided to finally bring my Fireboat out of the closet and up for inspection.
This is the first of my many boats I am showing, I will probably show others in the future.
I started to build her back in 2006 after being off work and having a shoulder operation. She was not going to be a R/C boat, just a bit of something to do whilst on recovery.

I have a 34" still in the box unmade, purchased back in 1994 from Aerokits.
I drew round all the parts and then shrunk them on my scanner. She is 27" long I think that's
just fraction over 1/20th scale . She is almost all balsa except the 2 under skins that are balsa laminated with 1/64th ply. The hand rails are 1/4" balsa blocks I cut from a strip and the rail is ally tubing.
The mast is made from plastic strip from packets from the model shop.

When I returned to work she was put into the shed and left unfinished.
I stumbled across the Fireboat website and registered in 2009 when I was off work once again. This then made me think more about working on her again and I decide to turn her into an R/C model. So out she came and I fitted an Electomax Delta 480bb motor and a M3sonik esc.
I also purchased a couple of Robbe fire monitors, put them together shortening the nozzles and cutting the bottom of the base of to try to look a bit moreto scale. I know they are not the correct type but if I want to go down the road of getting them working then these ones will.

Then off I went to Wilkinson's and bought some paint. Then set out to paint her, as I brushed on the paint it seemed to be drying almost as quick as I was painting her. Dragging the paint I had just put on with next brush stroke. What a TOTAL DISASTER !!. I gave up on her and back into the shed she went.

2010 arrived I started again rubbed the paint down a bit and bought some Tamiya spray acrylic and started spraying, underside red, it seemed look all right. I used a nice new roll of low tack masking tape, taped up the underside and the decking and sprayed on the black on the sides. I thought that look all right. Took off the masking tape, which also took off the red paint and the dope from the decks. Another DISASTER. Back in the shed she went once again.

A couple of months went by and I was up in Norfolk on my own boat and watching the workers in the boatyard, ideas came to me and when we returned home, out she came and I repainted the sides
and then with red oxide paint I painted her undersides to make it look like antI foul paint. I used some white stripe to cover the join of the two different paint colours.
I had bought some roundels in Anglia Model Shop in Gorleston and some lettering in a shop in Norwich and after painting put these on.
Not looking fantastic but passable I was a little happier with her, but still not satisfied, back in the shed she went again.

Now after so much nagging from my brother out she has come, I've started again. He talked me into changing and trying a brushless motor and a smaller esc he had in his tool box from his helicopter he was shelving as its rota head was damaged beyond repair.
I have now fitted them and if they work I will change the esc to a forward/ reverse esc in the future at some point.

Sea trials are still away off more than likely in the spring, because the decking has yet to be painted. That will be the next job.

I think that's all for now, as I have probably bored you all to tears. I hope update as I progress further.
Just to let you know I'm Tom (alias BOATSHED).