Just a simple model I built for my son about 14yrs ago. He wasn't interested (more into computers) so I use it for the salt water. Just a brass shaft and 12v high speed 380 motor, runs quite well. Ran it to try out the new 4K camera, (set on 1920x1080) but had to convert the vid from MOV to MP4 to edit it, so it reduced the clarity a bit. At least it doesn't have a blurry bit in the middle of the lens like my 10yr old one. have to figure out a better way, (or get a better editor)
Hi wunwinlo
This was built by another club member and sold on when he finished sailing models so we do not have the plan. It is a model of a Sea Plane tender and was probably built in the 1960's. It could have been a kit from the Maycraft stable or even Veron but also possibly built from a plan in Model Boats or its predecessors. Doug replaced the brushed 550 motors with two 2028 brushless arounf 1000Kv with scale 3 blade brass props and 11.1v LiPo 2200Ma. Models from this period are very nostalgic and I look forward to seeing your model some time in the future,
Cheers
Dave976
Thanks for the info on your model, Dave. I thoroughly agree that the 50/60's models of the 'RAF Navy' vessels have a lot going for them. There's nothing nicer than a planing hull and two hot brushless!
A short video to celebrate sailing 3 x 1/24 scale Fairmile D's as well as a Vosper 73' Type 1 at the same time.
Graham's boats are scratch-built onto fibreglass hulls.
My boats are totally scratch-built.
it is best viewed on a larger screen in HD.
Brilliant. Best war film I've seen in years.
My mtb's of mtb 389. Built 40 odd years ago and left in the loft where it collected dust and soot. When I retired I brought it down, fitted a Graupner 700 motor in and ran it on 14.4v. It plains very realistic. Thanks for the video...👍
Exploring the possibilities of a new sleeker look to the Wee Nips that I have built previously , - I created the "Slim Nip" just as a development from the original classic Graham Bantock design.
Length - 720mm
Beam - 166mm
Keel depth - 290mm
Mast height - 1130mm above the deck.
Maintaining the simplicity and convenience of a Uni rig , easy to transport , easy to rig , & no guys .
Result was : - a new look, light wind, high aspect ratio - "Slim Nip".
Back at Towne Lake for more fun and friendship. Had a good time, we saw 2 subs in the water, a few tugs, launches, working boats and an old MRP deep vee and a Micro Magic. I had a great time as I finally got my Italeri Vosper handling decently even in the windy conditions we had. A little more tweaking and she’ll be spot on, but I’m pleased with her for now.
Cash
Dave, just load up the boats, make a few sandwiches, drink a couple of Red Bulls and come on down!!🤣
Seriously, wish you could come. Hope you get to splash something soon.
Cash
Just a quick update with the new camera boat before fitting and running with the Gopro attached.
Observations :-
1. Maneuverability - Great - but better control with high and low rate options!.
2. Speed - Too much ? - may be , but enough for me to throttle back quickly !.
3. Camera - Good balance and rotation for 360*.
4. Cost - Minimal - ie. Motor & ESC kit from Hobbybitz.
5. Noise - 5/10
6. Fun Factor - 10/10 - just for fun ! - enjoy RC Sailing !.
NOTE - I would be interested to know of any theories in respect of the "PULSING NOISE" of the motor ?????
Cheers
Phil
Once again our intrepid members meet at Josey Ranch in Carrollton Texas to have fun, give each other a hard time and promote the hobby of model boating. 😀
Hi Graham, you've got it tacking nicely,-any way you can make it adjustable, (pic, - would require another servo) or are you just going to add stops. If not adjustable, you might as well keep it around the center which will give you max inhaul on the wind, and help keep the boom down, but not quite as great running. Unfortunately, one of those necessary performance adjustment problems with models, which can't be fixed without a lot of extra 'string'. A boom vang may help a bit as well,
I've added a couple of fixed end stops to the traveller as the easiest thing to try. They will help reduce the violent swing of the boom when it tacks. Just need a bit of wind to try it out now..
Here is a look at the boats at Sonstraal Dam, home of the Northern City Model Boat Club, where on 26 February the Annual Record Day hosted by the Western Cape Model Boat Club brought more than 140 boats to the dam.
While some were just floaters, and some sank trying, there was a good collection of models actually in action.
One of them was the 1,5m Steam Tug, Miamota
The video was taken with an iPhone mounted in front of the bridge of the Smit London Tug boat with LOA of 1.7m
The Juliana II - a Hampden plank-on-frame Schooner
This was my very first RC project. In fact, it was only to be a static model, but then things changed.
Currently she's a shelf-queen as the rigging takes a while.
She can be converted to a fishing boat and fitted with a 5 blade 42mm prop and brushed 540 motor.
The sail rudder is larger and requires the prop to be removed.
