HI Fellow Modellers,
Another model from the RADMC fleet at the fleetshaven workshop and boat yard in Ponthir.This model was built from a Caldercraft Kit, This model came into my possession for the price of 20p, a raffle prize at Bryn Bach Model Clubs OPen Day 2010, when it was built is unknown. The item being made for display use and not finished off, no internal electronic fixtures. Did have a prop shaft and prop that had not been fitted correctly. 50% of all the fixtures had to be removed and refitted before they fell off, some didn't stay in place from the show back home. The model was finised off using a photo of the Milford star on the internet. The fish boxes and figures being obtained off DON one of the Society members who had a mould to make them in white metal, only required cleaning up and finishing off. A graupner 6 volt steam unit is fitted in the funnel and to make the boat a little more realistic on the water,a maplin steam sound system has been used to generate the sound of the engine. A simple mod allows the revs to be linked to the engine voltage. The drive motor is a 550 with the lowest revs I had in MJB's this was married up to a 2.5/1 gearbox I also had in stock. The main motor and steam unit are supplied from a 7.2 volt nicad racing pack. This model has had meny fishing trips on Cwmbran Boating Lake and at shows the Society visit. Hope you enjoy the pictures, Regards GreyWolf.

HI fellow Modellers,
Another model from the RADMC fleet at the fleetshaven workshop and boat yard in Ponthir.This model was built using a Billings Kit, bought for me as a Christmas pressent in 2009. A graupner 6 volt steam unit is fitted in the funnel and to make the boat a little more realistic a maplin steam sound system has been used to generate the sound of the engine. A simple mod allows the revs to be linked to the engine voltage. The steam engine rotates using a stripped down minI servo, fitted under the motor housing on the deck, again linked to the main motor voltage. The two 9.6 volt AA batteries and control gear are mounted under the boats floor, forward locker, a minI servo for steerage is fitted under the rear seat and the receiver is located under the wood pile. Figures are self made from items obtained from the local pound shop. The modal can be seen sailing at Cwmbran Boating Lake or at shows the society visit. Hope you enjoy the pictures, Regards GreyWolf.

mdlbt.comdlbt.com/members/images/1077/1328788896-S.jpgm/members/images/1077/1328789028-S.jpg
more pictures

HI bit more deck works done winches crew , that's it for now,
Back on the shelf , to wait for running bits . time to back to trawler build......Larry..

Just a few more pics of ML1302, rudders and A frames are home made and scale brass props are used.

Both on display at Portis Head show
1/12 scale 33" and 54" long.

This is GRP hull and a part vac-formed cabin and the rest is scratch build using plastic card! Fittings are from my own range along with the crew. Prop shafts and "A" frames are home made along with the rudders which are to scale form John Lamberts drawings.
Two Groupner eco600 motors are used connected to a 6volt cell lasting around 3 hours running.

Scratch build of Dave Metcalf Lulonga river boat ,
ready for running gear and paddles but the cost for those is ?200 not cheap .
Will now go on the back burner till I saved up a bit ......LARRY...

Have had this boat 30 years .Started it for my eldest son but never finished. But now with two boys of his own I am determined to give it my best shot.
Completly stripped it, repaired delaminated sections,took out all the gear (motor,radio,servos) and started again.
I will update progress as time goes on but I am determined this will be on the water this year.

my boat is powered by a 26cc zenoah engine,I skinned the outside in real carbon fiber and the interior with carbon/kevlar.I use a spektrum DX3S 2.4ghz tx with a spektrum MR3000 marine rx.the boat is equipped with a killer bee remote kill switch that doesn't need any power source to work so it will still kill the engine instantly in the event of battery failure or broken wire or when I want to from the tx. the carbon fiber was hand laid and wetted out with a special resin,then around six weeks of hand sanding with different grades of wet and dry to get it super smooth,then polish.

I race with the BMPRS. I don't win much but I have loads of fun trying.

In the process of converting a revell 1/400 version of the Queen Mary2 into a working r/c model using pager motors in the pods instead of using propshafts to keep it as authentic as possible. Have put gearing in to turn pods so dont have to have a rudder. So far all tests have been successful and will shortly have all detailing done and have ballast sorted ready for test runs.