Latest photos prior to exhibiting at Abbergavenny on Sunday and Monday 3rd & 4th June.
Sorry about photo quality but camera is playing up.

This model was originally scratch built in 1964 by my Dad as a 15th birthday present for me,the length over all is 60.5" with a beam of 17.5" and a theoretical draught of 3.5",not sure as to the actual design but it is meant to be 1/12th scale, it was originally powered by a 12 Volt windscreen wiper motor out of an old Mercedes car, and the radio gear was a home made system as well, but both are now well beyond repair and I am fitting an MFA 800 Motor with a Fusion Aquapower ESC rated at 125amp. run by a new 2.4 Ghz radio system.
When I get to sea trials stage I will send Update and possible video footage.This boat along with the rest of my harbour, will be on view at the Abbergavenny Steam Rally this weekend June 3rd and 4th(Sunday Monday) in the model section marquee.

HI just completed/refurbished an old and somewhat poor and sorry MFJ Fairey Fantome, complete stripdown repaint and new shafts/motors etc.
Now for some water trials to see what mods are required.

This is a Deans Marine Kit which I built about 2 years ago. it is now fitted with a 180 watt 1100kv brushless motor running on 7.2 volts and using a Turnegy 18amp car brushless ESP. With a 35mm X type prop it FLIES.

Bought off ebay, where else! Had been started as a cruiser, with one very small electric motor,then put in a loft for goodness knows how many years.Replaced prop shaft with 2, 40mm r/h and l/h props, 2x 540 motors running through 40a esc.Radio is 27mhz. 2ch. would like to swap to 2ghz to get rid of the unsightly aerial! I am awaiting some plasticard windows to Improve the looks and will slowly add fittings as and when.I tend to sail it every now and again on the boating lake in BUXTON, no-one has shouted as yet,though I'm not sure the swans approve.!: The photo on the water was just as the power was running down, none as yet at speed.It is very manoeverable with the twin rudders,almost on the gunwhales at speed.

HI shipmates, here,s a few shpts of the "Port ".
She,s a 1/80 scale scratch built cargo ship of the Port line company from around the 1950,
A ship this size requieres quite a bit of balast, I use water, it takes around 40 lds to get her sitting right, this is pumped in and out with a submersible caravan water pump.
Most of the fittings are resin castings.
there are a few more bits to finnish off but could not resist the chance to try her out on the Chasewater pool.

HI fellow modellers, Another model from the RADMC fleet at the fleetshaven workshop and boat yard in Ponthir.This model was scratch built using a fibre glass hull and plan obtained from a fellow modeller at the Bridgend Show in 2007. The front door and some fittings are made from plastic card and tube, decks are from ply and timber. On board figures are from the pound shop and car boot sales, modified by myself. The on board tank and half truck are RTR models that I have modified their looks to fit into a WWII theme for the craft. This craft has twin drive, 400 motors via 2.5/1 gearboxes. I tend to use both sticks on the TX for drive as this allows me to turn the model on a six pence.The dispatch door works from a rotary pot on the TX and via a rotary sail winch servo in the hull. I have just modified my Planet 5 TX to allow me to change my radio gear in this craft. This model has had meny trips on Cwmbran Boating Lake and at shows the society attend during the year. Still haven't allowed the tank or half track to run off the landing craft up the lake side slipway. one day I might get it on video. Hope you enjoyed the photo's. Regards GreyWolf

This is GRP hull and a part vac-formed cabin and the rest is scratch build using plastic card! Fittings are from my own range along with the crew. Prop shafts and "A" frames are home made along with the rudders which are to scale form John Lamberts drawings.
Two Groupner eco600 motors are used connected to a 6volt cell lasting around 3 hours running.

my boat is powered by a 26cc zenoah engine,I skinned the outside in real carbon fiber and the interior with carbon/kevlar.I use a spektrum DX3S 2.4ghz tx with a spektrum MR3000 marine rx.the boat is equipped with a killer bee remote kill switch that doesn't need any power source to work so it will still kill the engine instantly in the event of battery failure or broken wire or when I want to from the tx. the carbon fiber was hand laid and wetted out with a special resin,then around six weeks of hand sanding with different grades of wet and dry to get it super smooth,then polish.

whilst being off work with cancer have spent three months building my polar trawler which I had to remake a lot of superstructure with plasticard due to the old ply delaminated. it has twin screws powered by two 400 motors and 40 amp esc and 6v sla. I think she looks quite good

A quick ( 3 weeks) rough 35" balsa MaiamI powered by Turrnigy 28/30 outrunner , 3cell LiPo and 30A ESC made for my son who wasn't that interested so I am adding a bit more to it and 'playing' with it myself .
Vic Smeed plan Thornycroft took about 20yrs (on and off) to complete and has an Electronize 43HX 24v 15A controller, 2x 400 sized 6-12v brushed motors 4cell 3000MAh LiPo for main power with seperate 3 cell LiPo running a computer fan for cooling (fan is linear and sucks air through the boat from the front hatches and blows it out through the rear hatches) There are also seperate 3 and 4 cell AA NmH packs for nav and interior lighting.
Boat runs 28mm 3 blade props and runs at a realistic scale speed and attitude. Radio gear is 2.4 and I have modified one TX for twin throttles and at present am running both these boats simultaniously on the one TX.
Have bought twin car ESCs, batts, RXs and BECs for the PT and the (36") British Power Boat 64ft HSL I am building (modelled on the RNZAFs 64ft HSL- the only one sold in the southern hemisphere - in 1940) Went on board as a teenager before she was ruined by being turned into a pleasure launch so it was a help with the building. Still remember the wonderful alloy 'Power Boat' stair treads down to the ward room. Will get some pics up of the HSL as well.

HI " I thought I would put my biggest model from my collection for all to look at ! HMS Avenger took approx 3 years to build . " She is a type 21 frigate at 1/64 scale . At 6 feet long . Scratch built on a fibreglass hull from plywood plastic card & metal parts . Works on a six channel futaba skysport .
Full working red & white leds on deck and cabin , lynxs helicopter with working rotor blades with landing lights. Working radars, bofor gun , A ships whooping sound . Runs on two speed 700 motors off a 12volt gel sell battery which give a good 1hr sailling time . Controlled by a 50 amp speed controller with two brass propshafts behind good size rudders which give a excellant turn .
My model HMS Avenger is a copy from the real ship in which took part in the Falklands war in 1982. Painted in the same grey with a green deck . She looks great on display or on the water . Avenger gets a lot of interest from the general public . please enjoy looking at the photos shown at Sheringham & Eaton park Norwich Norfolk .
" thank you .. A Prestney