Aquired as response to grandsons'Can't we have one like that' request on seeing other club members ' Hooligan boat'.
Cheap second hand commercial speed boat steered by shutting down port or starboard motors and only on/off on pretend transmitter.
Now modified with proper ESC, 2.4 radio with servo operated rudder and upgraded to take 8.4v NiCad.
Length: 30 inches_ Not yet sailed in modified form !
Looks like a nice mod on her. I have one but wasn't happy with it as it didn't have a very good radio range. But did go quite well in the radio range she had. That should be a lot better now you have done this to her. I gave my brother one that I got from a boot fair that cost me a £5er. He ripped out the insides and has fitted it with a small brushless motor and 2.4gh radio and it is not so much a hooligan but more of a total maniac. But good fun.
Presedent Perkasa Fibreglass hull
moving along nicely all running gear installed 2 x 1400kv EDF Motors with 2 x 90amp watercooled esc,s running on 2 x 11.1v 5000mah or 2 x 14.8v 5000mah twin rudders 45mm X props if it runs anything like my other one I will be happy still lots of finishing touches to be done
complete scratch built on a glass fibre hull here are a few more photos to show the progress that has been made still a lot of work to do boat powered by a540 motor driving a 60mm 3 bladed prop I sail at pickie pool in bangor co down Robert waterson angus
alan the hull is fibre glass scale model of new venture moulded by bill wood for me she is same scale and design as my own fishing boat was built early 70s all the rest is totally scratch built from my original drawings glad you like it winch lights radar all wired up and working I hope to give it arun out on next sunday morning allgoing well will put some pictures on afterwards rgds r w angus
This was the 1-35 scale plastic model kit and converted to RC 3 props 2 working port and the starboard the centre is non running. Due to weight I used a 11.7 lipoly battery so it's fast but the running time is only about 20 30 mins
It won best in show in the navy boat section at our club due to the detail and the figures so can't be bad
Bought this part built with prop propulsion . but Im converting it to paddle power.
im using a 600 motor with a 50/1 gearbox to power it , but I think I will have to change the setup as the noise is too loud ,even though it will
Eventually it will have a 'Dixi' sound system installed .
wheelhouse plus some deck planking in place deck planking complete plus gunnel cappings complete boat completely scratch built on a fibre glass hull working winch scratch built boat powered by a 545 motot driving a 60 mm 3 blade prop Robert waterson angus
What is the length of this model? I am still engaged in flying scale WW1 airplanes at 83, but I can see me getting back to my Bristol Pilot Cutter and Clyde Puffer.
Thanks Sandy it is seriously fast two 1400kv motors running on 4c 5000mah lipos 90a watercooled esc I have just sold it as I am nearly finished building another Perkasa with the same running gear the deck fittings & armaments are from Battlecraft I will post some pictures soon regards Bob
Started 1 Oct 2014. Designed by Bennett to take an action man figure. I decided to use a drawing manikin. First try was without manikin and a great success. Still working on it to get Manakin rowing properly. 8Th feb tested and a sucsess but does not like strong wind.
Designed by Vic Smeed in 1964 for the Magazine, Model Maker. Plan No. MM812. Found plans for free on internet and decided to build it as I did not have a vintage motor boat in my collection. Did not like the cabin so redesigned it. Powered by a Johnson 600 motor,2 * 7.2v 3300 mAh battery, 20 amp Mtroniks Viper Marine Controller and a 45mm dia course 2 bladed propeller. Goes really well.
Fitted trim tabs which finished the boats performance. Tested in rough weather and got 20 mins running on a fully charged battery.
Hello, I found this old kit and I'm building, they were so many years that I did not do modeling and I'm just having fun with this nice little boat.
My kit is marked "Vladika Model", but is also produced by Aeronaut, having no patterns or instructions I have relied on the aeronaut, found (in German sob...) on the internet, and looking the photo on the box.
On the box it says it works with a Speed400 reduced 3: 1 with a (bad) 3 propeller blades 40mm, but I put a simple speed 600 20T with a 4-bladed propeller brass 45mm bought on ebay in singapore
Hull hollowed out and some bits from a static display model, based on several photo's of Greek fishing boats, Fish boxes from Coffee shop stirrers, Fish from long grain rice, Crew from Pound shop (Soldiers chopped & reshaped. ) She sails fairly well on first trial at Weymouth & Portland MBC, Miles Cross Farm lake .
Spec: M'tronics Vision 400 brushed motor, M'tronics 15a ESC, 12v SLA battery, 3 blade 30mm Prop. with Led Navigation and deck lights.
Found this Dense block of foam, floating in local Ashton Canal, whilst sailing other boats with my brother, whilst rescue a stuck boat from the reeds, in 1996 was temporarily on the dole at the time, struck by her Landing craft shape on turning it over plus realised I could carve it like wood, later using my bits box, after carving a couple of box shaped groves, for battery, motors and rc equipment, literal rammed a prop shaft, and rudder shaft through hull, and fashioned some balsa sheet into superstructure suitable camouflaged , I had a "US Army Vietnamese River Craft" of sorts and with its 1 1/2 to 2" thick Hull virtually unsinkable, hence its name :-). Here she is in 2000 sailing at Ethrow Park. May in the future alter her superstructure, she makes a handy towing barge for both mine and my brothers Tug Boats, and if rc left connected can even act as rescue boat if they pack up or get weeded up :-) - Have delete this from You Tube and replaced with slightly clearer version, but it seems to be still working here mysteriously, may cease working eventually, new version above :-)
