My three latest aquisitions: a pleasure launch, a speed boat and a landing craft rigged out for the Vietnam war. The landing craft is ready to go, as is the speed boat (speed boats not my thing to be honest) but the pleasure launch will be a project. I intend to replace the upper cabin, strip the paint and maybe just varnish the hull, add some planking for the deck plus it needs all the running gear....should keep me busy for a while

Video of the first start-up and test of "Sweet Sue" in dry dock. All went well ! Had two sails on water since.I built this vessel from scratch using a pre made clinker fibreglass hull purchased from Mini Steam Australia. The engine is an oscillating twin cylinder and the boiler is a 3" Centre Flue Gas Fired Vertical Boiler from "Miniature Steam". The gas tank is a 1-1/2" vertical refillable GasTank also from Miniature Steam Pty. Australia. The vessel is radio controlled with the skipper appearing to control the rudder. it has a smoke generator and a rc controlled steam whistle.

Coal fired Clyde Puffer project. GRP hull with vertical boiler and oscillating engine both of which i made from scratch. Goes very nicely . pictures taken at ilfracombe boating pond. Les Breame

Hull is from boot sale. Turbine is 3" dia and is driven by twin boilers. I made them both. Speed is not blistering but it goes !!! Boiler pressure is 100lb/sq in. Les Breame

This is my 6 month in build of a fully working fishing boat .she has a real I have modified and put a 20kg winch servo so u can real in and out and have drill a hole in to the real and put another servo so u can lock the reel out to.made a back plate on the end of a cut off rod and bolted in to the hull. She has full fpv from the wheel house with a 360 spin HD camera and have even put a digital amp meter so u can look at to and see how mUchida power u have left full running lights controls off hand setc to twin brushless motor water cooled and a large 100 amp esc with air fan and own power supply going to take her out tomorrow for her maiden voyage. Witch has bin a real long time coming and a lot of blood sweat and stress to get it all to work but finally I'm there hope u all enjoy and like what I have dun thanks for reading my post Ben

I bought a used hull of the Ayton Cross and look all over the internet for some plans but found none.
I did find a lot of images though.

I bought most if not all of the fittings and since have decided that the way to go is to make what you can from what I can get hold of.

So all other model boats are and will be scratch made.
I have two on the burner at the moment.

Anyway some of the Ayton Cross looks right some of it does not.

But I can always do it again as I hopefully get a little better.
This one again is awaiting Ballast and it will be ready to go.
I fitted two Engel 12 volt motors and made the mounts in grp then Laminated them into position..

Everything has been hand painted and slightly aged .

The bow thruster was made using some household plumbing pipe a small propshaft Again home made and it works very well.

Something to play with as I build hopefully better.

Well this is the 3rd version I have made of a springer tug.

Grp Hull and this time using 2 mm plastic.
Balsa wood and again what ever I could find laying around.

The decking is just printed paper and stuck down with Varnish.

Just needs some ballast and it is ready to go.

So this was attempt number two at a springer tug.. A little better than the very first one.

Again a home made grp hull and everything else Balsa wood and a few bits I could find about the house..

Well this one too has been scrapped and the hull reused.
Or set aside for another one at a later date.

So at this time is just a fitted out hull

Well this was the very first model boat i made.
A springer tug.
I made a mould and then made a few just in case i was to the point of everything going wrong at least I could start another one.

Apart from the home made GRP hull everything else was made in Balsa wood.

Since been scrapped but the hull and all the electrics ect have been reused again for another version..

Basically scratch Built except for the hull supplied by Fleetscale
Scale 1:48
Canadian Corvette and powered by single screw Saito steam engine
Lighting throughout with bilge pump and Asdic sound system
Sails scale speed beautifully with smoke generator adding realism
To steam power

I built this vessel from scratch using a pre made clinker fibreglass hull purchased from Mini Steam Australia. The engine is an oscillating twin cylinder and the boiler is a 3" Centre Flue Gas Fired Vertical Boiler from "Miniature Steam". The gas tank is a 1-1/2" vertical refillable GasTank also from Miniature Steam Pty. Australia. The vessel is radio controlled with the skipper appearing to control the rudder. it has a smoke generator and a rc controlled steam whistle.

Scratch Built on a GRP Hull 10 years ago