This is a Kitshack 46 inch Crash Tender. Nearly finished with a bit more detail yet to finish powered by 2 1400 kv brushless motors running on car speed controllers at 7.2 volt. Goes like stink! Has working rotatable fire monitors which are scratch built

Finally Finished touching up the paint after it being unused for over 5 years and now working better than before, after putting a new brushed 280 motor into the boat. The boat is roughly 850mm long and 141mm wide and was built by my late Grandfather when I was little.

Scratch built some years ago, powered by 6volt PB battery.
She was always very slow and hard to manoeuvre. She was made from MM plans. I could never get her to behave in the water. 27Mhz TX/RX. tried changing motor, prop 6 to 12 volts nothing seemed to make much difference, gave up in the end. You can't win them all.

SemI Kit, I.e fibreglass hull and superstructure and wooden rubbing strake all the rest is scratch built. A very good sailer and very stable. Quick to build only a month and powered by 540motor and 35mm prop. Lasted for hours on one charge.

Can anyone please tell me if they know what this model is or should be as it was given to me by an old gentleman who also did not what it was or should be

HI I got this Aerokits Solent Class life boat at the weekend last .it need a lot of work to be done .can any one tell me anything about this life boat

cliff

Just started work on the Torpedoes for My Aerokits PT Boat, the ones in the kit don't look quite right,

Finally Finished my ebay refurb, Sailing @ Mutual Model Boat Club Heywood

100% scratch built model of the Toronto harbor Fireboat. Been in the making for almost five years now. When finished it will be RC and have water pumping capabilities. Toronto Fire Services are celebrating the boat's 50th anniversary this year and appear to be interested in my model. The boat will be powered by two Dumas six volt motors geared three to one.

SS Talacre - Single Hatch Coaster 1:48 Scale Just recently bought second hand and about to renovate to my own standard!
Caldercraft SS Talacre
The SS Talacre is a typical single hatch coaster used in the coal trade of a type that was found by the hundreds around the coast of the U.K. in the golden era of steam. Designed for Point of Ayr Collieries by Crichton, Thompson & Co Ltd., of London she was built by Crabtree &Co., of Great Yarmouth in 1917. Talacre was named after a small village near the colliery. Talacre was finally scraped in 1959 by the Hammond Lane Foundry in Dublin. Realism leaps out of the completed model, as if a turn of a valve will start the anchor windlass or the cargo winch clattering away and the lagged steam pipes to begin steaming and drying out.
Scale: 1:48
Length: 863mm
Beam 152mm

I made a wooden barge for my tugs to pull but found this too heavy so I asked my old firm to make me one in 4mm aluminium it has been fully seem welded and is water tight .I got them to powder coat the whole barge in black matt and I just added the red paint. The top just slides off so I can change the cargo I just wish that I had not made this so deep as it sits high in the water unless I add a load of ballast am using a 10 ltr water container at the min and its still work in progress

here are my three boats, oakgarth 42" twin screw 4 blade props with kort nozzles she also has a working bow thruster.She running two speed controllers off a 12volt sla battery and has full working lights I would love to say I built her but I never, all I have done is added lights and give her a full makeover. Next is Doug the26" pusher tug twin screw 3 blade props full working lights and water jet single speed controller futaba radio set up I have just changed the crane on this again I have only done cosmetics to this tug and my last boat is a 20" seaport tug this is what my grandchildren sail and for 60 quid its great thay love it .the paddling pool was 15 quid for argos and perfect for testing well better than filling the bath .