This tug boat is almost finished, she is based om my fiberglass hull. Power is 2x Speed 700, lenght is 104 cm

I just finished this ship, based on my Fiberglass hull. Ship is powered by 3x Speed 600 with gearboxes 3:1

This model was built from scratch except for the fiberglass hull, using styrene. The drives are Graupner VSD's and the 10 fire monitors are powered by BMW windshield washer pumps. The radio is a Spektrum DH 6 with a twin stick modification and fitted with a switch 8 to individually operate the monitors.

Here is a video of our boat (Vigilant star) sailing at New Brighton boat lake on the wirral every Wednesday.

The boat is a semiscale (Coast Guard Cutter), designed by Hal-Harrison in Marine Modelling. I have doubled its size and put two 540/1 Mfa motors in, driving quanta 45mm props. She is 36" length 8" Bow, runs of one 12 volt 7Ah SLA battery.

It is made from Balsa/Fibreglass resin. Runs well no leaks to date. Gerry.

This is one of the Aerokits models, however it has recently been stripped down to the wood to apply a fibreglass coating.

These video clips show the boat undergoing trials before being completly re-fitted.

this model was made by me from scratch of the london tug Ionia 56 inches long 12inch beam she has a bow thuster fitted to help the steering nav lights and cat diesel sound generator and its very heavy thats why its not in the water very often I getting to old to lift it in at 73 its a young man boat the hull is fibraglass but it looks so well in the water .

This tug is in scale 1:25, used two 900 motors. Still need a lot of details. Models are based on my own fiberglass hull

This tug is based on my own fiberglass hull. She is 91 cm long, two Schottle drives with Speed 900 motors

This is the Hugh William Viscount Gough. She is a solent class lifeboat. She went into service in 1963 as the Stornoway lifeboat. She was there for around twenty years.

She then went on to Barra and ended her service at Dunbar. She was sold in 1993 and is now out in Malaysia.

I have scratch built her from the hull up. She has a fibre glass hull and the super structure is made from plasticard. She took four weeks to build. I have some bits and bobs to do to her.

She runs on two MFA 850 torprdos, but I am going to down size to 800's.

We sail her at Mote park Maidstone most Sundays and also at shows.

She is 48" long with a scale of 1:12

The hull of this model was my own design in 2004 and was sailed for 2 years, and then a new upper decks and battery system were added during the winter of 2005. The hull performed well enough but my original cabin design was too crude to keep.

The boat shown here depicts my effort to copy a 1958 ChrisCraft Cabin Cruiser at a scale of 1" = 1'.

The hull is 1/8" thick pine planks on frames with hand cut Walnut decking and 3/16" Walnut cabin sides. No epoxy or glass was used on the hull - just a good paint job.

The big change was to replace a bulky & heavy 12VDC leac acid battery with 9 AA dry cells connected in series. Bathtub testing indicated I could expect about 2 hours running time at full speed and that estimate was about right. A Dumas 12VDC motor and mechanical speed control were used with a JR XR 2 control.

The reduction in battery weight made a very large speed and appearance difference. Availability of the AA cells was an economic plus.

"BOO BOO Kitty" is a scale model of a Crosby designed Cape Cod Cat Boat.[USA] it was built from scratch at a scale of 9.04" = 1"; the model being 26.5" oal.

The dimensions were taken from a book that highly detailed the building of a real Cat Boat.

The hull is plank-on-frame with epoxy and glass cloth as the final surface. A separate and detachable fin keel was used for sailing of the centerboard model.

Radio controls were a Hitec sail winch [HS-785HB] and one servo for the rudder with a 2 channel JR transmitter.

Copying the book plans, scaling them down, and construction took up the winter of 2006/2007. The model is sailing better than anticipated on a local lake in Langhorne, Pennsylvania.

John called this model "Nancy Dancer". it started of with plans from 'Nexus Plans Service' for Vic Smeed's 'Vivacity'. John used the hull only plans and created everything else himself. it ended up LOA 49" with a beam of 17". With the 12VDC battery the weight came to 23 1/2#.

Because of his basic 'Sedan Cruiser' he designed all the mechanicals and electricals beneath the main cabin floor, including the battery. There was quite a bit of detail put into the main cabin - unfortunately not shown in the photos - including a galley, eating area, furniture and the helmsman's station. The scale is 1" = 1ft.

This hull is plank on frame using 1/8" pine planks. Below the waterline there's epoxy & glass and above there is just epoxy. All the brightwork, cabin housing & decks is natural Cherry with a clear urethane finish.

The power is a Dumas 12VDC motor with a mechanical speed control. The bottom photo shows that he added a 2:1 gearbox to the motor and ran it in reverse to increase the prop RPMs. He also included a constant running fan to cool the motor due to the confinement of the space.

The single propellor is 2" - 2 pitch - 3 bladed bronze. As on all his models he used a 2 channel JR XR2 75 mhz.